Duratech DuraCover DCTS-450 Manuel page 83

Étape 5 : Fixez l'« assemblage à bride soudée ».
Côté
palier
Montez l'« assemblage à bride soudée » à l'intérieur du bassin de la piscine à l'aide de quatre « boulons à tête
fraisée M8 x 70 mm » (501-0146). Enlevez le liner en papier blanc côté arrière du « joint EVA » noir (510-0244) et
collez-le sur la face avant de la « bride arrière en PVC » (510-0270). Fixez la « bride arrière en PVC » à l'aide de
quatre rondelles SST (504-9043) et de quatre « écrous de blocage en nylon » (504-9044).
Étape 6 : Appliquez le « joint en silicone ».
(510-0224)
Enlevez le liner en papier blanc côté arrière du « joint
en silicone » bleu (510-0224) et collez le joint sur la «
bride soudée assy ». (côté moteur)
Assurez-vous que les six trous dans le joint sont
correctement alignés avec ceux de la « bride SST ».
164
Étape 7 : Montez le « fond du support »
(510-0217).
Côté
palier
Montez le « fond du support » sur le « joint en silicone
» à l'aide des six des boulons fournis « M8 x 20 mm »
(504-0142) et des six « rondelles en nylon ». (504-0141)
Assurez-vous que les boulons sont suffi samment
vissés.
Étape 8 : L'installation « côté moteur » est
terminée.
Côté
palier
Étape 10 : Percez 4 « trous de montage ».
Côté
palier
Diamètre de perçage : 9 mm
C
TOP TOP
Make sure the sticker is aligned Make sure the sticker is aligned
properly before drilling. properly before drilling. This sticker is used in This sticker is used in
the following situations: the following situations:
Drill center hole Drill center hole Wall Duct Wall Duct
of 36,00 mm only of 36,00 mm only (Bolted) (Bolted)
on Motor Side! New Construction: on Motor Side! Stainless Steel, PE or PP swimming pool. (Thin Wall) New Construction: Stainless Steel, PE or PP swimming pool. (Thin Wall)
Steel or Wooden swimming pool with Liner. (Thin Wall) Steel or Wooden swimming pool with Liner. (Thin Wall)
Wall Duct (Built-On) Wall Duct (Built-On)
Renovation: Brickwork swimming pool with Liner. Renovation: Brickwork swimming pool with Liner.
New Construction: Brickwork swimming pool with Liner. New Construction: Brickwork swimming pool with Liner.
C
TOP TOP
Make sure the sticker is aligned Make sure the sticker is aligned
properly before drilling. properly before drilling. This sticker is used in This sticker is used in
the following situations: Centerpoint the following situations: Centerpoint
Drill center hole Drill center hole
Wall Duct (Bolted) Wall Duct (Bolted)
of 36,00 mm only of 36,00 mm only
on Motor Side! New Construction: on Motor Side! Stainless Steel, PE or PP swimming pool. (Thin Wall) New Construction: Stainless Steel, PE or PP swimming pool. (Thin Wall)
Steel or Wooden swimming pool with Liner. (Thin Wall) Steel or Wooden swimming pool with Liner. (Thin Wall)
Dia. 16,0 mm Wall Duct Dia. 16,0 mm Wall Duct
(Built-On) (Built-On)
Renovation: Renovation:
Renovation: Brickwork swimming pool with Liner. Brickwork swimming pool with Liner. Brickwork swimming pool with Liner. Renovation: Brickwork swimming pool with Liner.
New Construction: New Construction: Brickwork swimming pool with Liner. New Construction: New Construction: Brickwork swimming pool with Liner.
Brickwork swimming pool with Liner. Brickwork swimming pool with Liner.
Dia. 9,0 mm Dia. 9,0 mm
Drill holes Drill holes New Construction: New Construction:
with Dia. 9,0 mm with Dia. 9,0 mm Stainless Steel, PE or PP swimming pool. Stainless Steel, PE or PP swimming pool.
when using M8 Bolts. when using M8 Bolts. Steel of Wooden swimming pool with Liner. Steel of Wooden swimming pool with Liner. Dia. 36,00 mm
Dia. 40,00 mm
Drill holes with Dia. 16,0 mm Drill holes with Dia. 16,0 mm Centerpoint Centerpoint
when using Chemical Anchor Resin. when using Chemical Anchor Resin.
BOTTOM BOTTOM BOTTOM
Dia. 16,0 mm Dia. 16,0 mm
Renovation: Renovation:
Brickwork swimming pool with Liner. Brickwork swimming pool with Liner.
New Construction: New Construction:
Brickwork swimming pool with Liner. Brickwork swimming pool with Liner.
Dia. 9,0 mm Dia. 9,0 mm
Drill holes Drill holes New Construction: New Construction:
with Dia. 9,0 mm with Dia. 9,0 mm Stainless Steel, PE or PP swimming pool. Stainless Steel, PE or PP swimming pool.
Dia. 36,00 mm
when using M8 Bolts. when using M8 Bolts. Steel of Wooden swimming pool with Liner. Steel of Wooden swimming pool with Liner.
Drill holes with Dia. 16,0 mm Drill holes with Dia. 16,0 mm Dia. 40,00 mm
when using Chemical Anchor Resin. when using Chemical Anchor Resin.
Les outils affi chés ne correspondent pas aux outils BOTTOM BOTTOM BOTTOM
requis réels ! Veillez à utiliser les bons outils !
Étape 9 : Appliquez l'« autocollant de
perçage C ».
Côté
palier
Y Y
X X
Y Y
X X
C C
TOP TOP TOP TOP
Make sure the sticker is aligned Make sure the sticker is aligned
properly before drilling. properly before drilling. This sticker is used in This sticker is used in
the following situations: the following situations:
Drill center hole Drill center hole
Wall Duct (Bolted) Wall Duct (Bolted)
of 36,00 mm only of 36,00 mm only
on Motor Side! New Construction: on Motor Side! Stainless Steel, PE or PP swimming pool. (Thin Wall) New Construction: Stainless Steel, PE or PP swimming pool. (Thin Wall)
Steel or Wooden swimming pool with Liner. (Thin Wall) Steel or Wooden swimming pool with Liner. (Thin Wall)
Wall Duct Wall Duct
(Built-On) (Built-On)
Renovation: Brickwork swimming pool with Liner. Renovation: Brickwork swimming pool with Liner.
New Construction: Brickwork swimming pool with Liner. New Construction: Brickwork swimming pool with Liner.
C C
TOP TOP TOP TOP
Make sure the sticker is aligned Make sure the sticker is aligned
properly before drilling. properly before drilling. This sticker is used in This sticker is used in
the following situations: Centerpoint the following situations: Centerpoint
Drill center hole Drill center hole Wall Duct Wall Duct
of 36,00 mm only of 36,00 mm only (Bolted) (Bolted)
on Motor Side! New Construction: on Motor Side! Stainless Steel, PE or PP swimming pool. (Thin Wall) New Construction: Stainless Steel, PE or PP swimming pool. (Thin Wall)
Steel or Wooden swimming pool with Liner. (Thin Wall) Steel or Wooden swimming pool with Liner. (Thin Wall)
Dia. 16,0 mm Dia. 16,0 mm
Wall Duct (Built-On) Wall Duct (Built-On)
Renovation: Renovation:
Renovation: Brickwork swimming pool with Liner. Brickwork swimming pool with Liner. Brickwork swimming pool with Liner. Renovation: Brickwork swimming pool with Liner.
New Construction: New Construction: Brickwork swimming pool with Liner. New Construction: New Construction: Brickwork swimming pool with Liner.
Brickwork swimming pool with Liner. Brickwork swimming pool with Liner.
Dia. 9,0 mm Dia. 9,0 mm
Drill holes Drill holes New Construction: New Construction:
with Dia. 9,0 mm with Dia. 9,0 mm Stainless Steel, PE or PP swimming pool. Stainless Steel, PE or PP swimming pool.
Dia. 36,00 mm Dia. 36,00 mm
when using M8 Bolts. when using M8 Bolts. Steel of Wooden swimming pool with Liner. Steel of Wooden swimming pool with Liner.
to to
Drill holes with Dia. 16,0 mm Drill holes with Dia. 16,0 mm Dia. 40,00 mm Dia. 40,00 mm
Centerpoint Centerpoint
when using Chemical Anchor Resin. when using Chemical Anchor Resin.
BOTTOM BOTTOM BOTTOM BOTTOM
Dia. 16,0 mm Dia. 16,0 mm
Renovation: Renovation:
Brickwork swimming pool with Liner. Brickwork swimming pool with Liner.
New Construction: New Construction:
Brickwork swimming pool with Liner. Brickwork swimming pool with Liner.
Dia. 9,0 mm Dia. 9,0 mm
Drill holes Drill holes New Construction: New Construction:
with Dia. 9,0 mm with Dia. 9,0 mm Stainless Steel, PE or PP swimming pool. Stainless Steel, PE or PP swimming pool.
Steel of Wooden swimming pool with Liner. Steel of Wooden swimming pool with Liner. Dia. 36,00 mm Dia. 36,00 mm
when using M8 Bolts. when using M8 Bolts.
to to
Dia. 40,00 mm Dia. 40,00 mm
Drill holes with Dia. 16,0 mm Drill holes with Dia. 16,0 mm
when using Chemical Anchor Resin. when using Chemical Anchor Resin.
BOTTOM BOTTOM BOTTOM BOTTOM
Appliquez l'« autocollant de perçage C » (403-
0371) à l'intérieur du bassin de la piscine et assurez-
vous que l'autocollant se trouve dans une position
correcte, avec le côté droit au-dessus. Déterminez
X et Y en fonction du diamètre externe des lamelles
ainsi que du type d'installation.
Étape 11 : Installez la « bride avant SST ».
Côté
palier
C
TOP TOP
C
TOP TOP
Retirez
l'autocol-
Dia. 36,00 mm
to to
Dia. 40,00 mm
lant B
BOTTOM
Enlevez le liner en papier blanc côté arrière du « joint
en silicone » bleu (510-0242) et collez le joint sur la
Dia. 36,00 mm
to to
Dia. 40,00 mm
BOTTOM
face arrière de la « bride avant SST ».
165