AirKing AKF50 Manuel D'opération page 4

5. Install the reflector onto the grill by placing the slots on the side of the reflector over the
lens clips near the center of the grill. While squeezing the middle of the reflector, slide it so
that the plastic notches rest under the lens clips and the reflector feels secure (Figure 13).
Slot
Figure 13
6. Install the grill (with reflector) by squeezing the two ends of the springs together and installing
them up into the slots on the fan's housing. Push the grill up into position (Figure 14).
Figure 13
7. Restore power and test your installation.
SECTION 7
Setting the Humidistat
This fan may be equipped with a humidity sensor that automatically turns the fan on when
humidity is above set point and off when humidity is at or below set point. If the fan is operating
too long or not enough, first check to see the humidity sensor set point. In cases where the
ambient humidity level of the room rises higher than the preset level, the fan will turn on even if
the room is not occupied. This helps prevent conditions that lead to mold growth.
CAUTION:
SERVICE PANEL BEFORE SERVICING THE UNIT.
1. To set the desired humidity level of the room, remove the grill and locate the
dehumidistat dial located on the wire compartment cover.
2. Set the dial to the relative humidity you want the fan to maintain usually between 50 &
80%. Moist climates will require higher settings than dry climates. When the humidity
level of the room is below this setting the fan will remain off. When the humidity level
rises about this setting the fan will turn on and run until the humidity level falls below
this setting.
3. Reinstall the grill and restore power.
210572203 Rev. N 1-16
Clip
MAKE SURE POWER IS SWITCHED OFF AT
SECTION 8
Use and Care
CAUTION:
SERVICE PANEL BEFORE STARTING INSTALLATION.
Cleaning the Grill: Remove grill and dislodge reflector from grill by sliding the reflector
1.
notches from beneath the lens clips on grill. Use a mild detergent, such as dishwashing
liquid, to clean then dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING
POWDERS. Completely dry grill before reinstalling. Clean reflector using a dry cloth. Refer
to instructions in Section 6 Completing the Installation, to reinstall reflector and grill.
2. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently vacuum the fan.
NEVER IMMERSE ELECTRICAL PARTS IN WATER.
CAUTION:
Changing the Lamp: Disconnect power to the unit. Remove grill by pulling downward
3.
on grill and squeezing grill springs together to release from housing (Figure 13). Remove
Reflector from grill by sliding the reflector notches from beneath the lens clips on grill.
(Figure 12).
Fluorescent Bulb: Remove lamp by gently twisting the lamp base counterclockwise while
applying outward pressure. Installation is the reverse of removal. Replace with Air King
model 26SBL or a compatible GU24 26 watt self ballasted lamp.
LED Bulb: Remove lamp by gently twisting the lamp base counterclockwise while applying
outward pressure. Installation is the reverse of removal. Replace with Air King model
AK6LED40 or a compatible GU24 6 watt LED lamp.
Night Light: Unscrew night light bulb from socket and replace with a 4 watt maximum type
C7 (candelabra base) night light bulb.
CALIFORNIA RESIDENTS ONLY:
WARNING:
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.
WARNING:
[OR CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
REPRODUCTIVE TOXICITY.
www.airkinglimited.com
MAKE SURE POWER IS SWITCHED OFF AT
ALLOW BULBS TO COOL BEFORE REPLACING.
THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL
4 of 12