Scrapping And Disposal; Accessories; Use - Intec 23402 Manuel D'utilisation Et D'entretien

3. Loosen screw POS. 13 - 23402 POS. 13 - 23402
assembled.
4. Fit the handle (the air distributor must be facing the pistons) inserting the coupling in the groove , put the parts removed
previously into the hole of the handle, tighten screw
5. Connect the two air pipes between the jack and the handle with the quick couplings on the chassis respecting the colour
indication as showed on the sticker on the chassis itself. DWG. 1
CONNECTION T CONNECTION TO THE COMPRESSED AIR SYSTEM O THE COMPRESSED AIR SYSTEM
- Compressed air enters into the jack circuit through the quick coupling on the top of the manual lifting/descending controls;
it is therefore necessary to have a connecting pipe with a quick coupling compatible with that of the jack. Check that the air
supply pipe has a useful passage of at least 6 mm and it is not pinched or restricted anywhere. DWG. 12
WORKING AIR PRESSURE: 8 - 10 BAR WORKING AIR PRESSURE: 8 - 10 BAR
- Absolutely never put the following into the compressed air circuit: hydraulic or Vaseline oil, brake liquid, kerosene or other
liquids.
-Install a filter dehumidifier-lubricator unit in the compressed air system.
- If you want to lubricate the compressed air circuit use exclusively:
AGIP OSO 100; MOBIL DTE 27; ESSO TERESSO 100; AGIP OSO 100; MOBIL DTE 27; ESSO TERESSO 100;
SHELL TELLUS 100; BP ENERGOL HP 100 SHELL TELLUS 100; BP ENERGOL HP 100
The manufacturer is not liable for any damage resulting as a consequence of disregard for the above indications The manufacturer is not liable for any damage resulting as a consequence of disregard for the above indications
and the warranty conditions are invalidated thereof! and the warranty conditions are invalidated thereof!

SCRAPPING AND DISPOSAL

SCRAPPING AND DISPOSAL
- The lubricants must be disposed of in compliance with the anti-pollution laws in force.
- Scrapping the jack and its component parts must be carried out by the user in accordance with current laws.

ACCESSORIES

ACCESSORIES
The jack is supplied with two extensions or height adapters (120 mm the long extension, 70 mm the short extension), a
circular tooth plate (10 mm plate) and an extension holder.

USE

USE
IMPOR IMPORT T ANT ANT: The jack must be used and operated in the horizontal position only in order not to compromise its : The jack must be used and operated in the horizontal position only in order not to compromise its
operation. operation.
- Follow the safety rules given in this manual to the letter.
1. Position the jack beneath the support point indicated in the vehicle manufacturer`s manual.
The manufacturer shall not be held liable for any damage to the lifted vehicle or other property, or for injuries,
caused by incorrect or improper use of the jack.
2. The handle positioning lever (A) DWG.13
locking system, allowing the operator to choose one of the three possible handle positions.
3. When the control (B) DWG.13 (B) DWG.13 is perfectly centred, the jack is in the rest position.
4. Turning the control located near the handle (B) DWG.13
raise the load.
5. Turning the control located near the handle (B) DWG.13
lower the load.
14
from the chassis and remove parts
POS. 13 - 23402 POS. 13 - 23402
DWG. 11 1
(A) DWG.13 is located to the left of the operator; moving it upwards frees the
(B) DWG.13 to the right from the operator`s point of view makes the jack
(B) DWG.13 to the left from the operator`s point of view makes the jack
POS. 9, 10, 11, 12 - 23402 POS. 9, 10, 11, 12 - 23402
and then tighten nut POS. 14 - 23402 POS. 14 - 23402
DWG. 12
EN EN
keeping them
.