Maintenance And Storage - LUND 67091 Notice Originale

GB
Appliance assembly and disassembly
Take the vacuum cleaner, the dust container and accessories out of the packaging and remove all packaging components. Place
the vacuum cleaner on the fl oor and install the dust container.
Before fi rst use, make sure that the container has all components and is correctly assembled.
If the container is mounted on a vacuum cleaner, it must be removed. Grasp the handle and press the container latch button (II)
with your fi nger, then remove the container from the vacuum cleaner.
Turn the top cover of the dust container so that the mark on the lid indicates the open padlock (III) symbol. Then remove the
cover (III).
Pull out the top fi lter of the dust container, check if there is an additional sponge fi lter under the non-woven fi lter. The uneven
surface of the fi lter (IV) should be visible.
Pull out the bottom fi lter of the container. Check the condition of the fi lter to ensure that it is not damaged. Open the bottom cover
of the container (V) by pressing the latch button. Check the condition of the cover seal.
Close the bottom cover. Install the bottom fi lter. Make sure that the tabs around the top edge of the fi lter hit the correct recesses
in the container (VI). Tabs and recesses are of diff erent sizes and only one mounting position is correct.
Install the top fi lter (VII). A correctly installed fi lter should have an top surface parallel to the edge of the container.
Install the dust container cover. Place it on the edge of the container so that the edge of the cover fi ts the edge of the container
around the entire circumference, the tabs of the lid should hit the recesses of the container and the marker of the lid should indi-
cate the symbol of an open padlock. Turn the cover so that the cover marker indicates the locked padlock symbol (VIII). Check
that all the tabs on the lid have slipped between the safety tines and the edge of the cover is fi ts the edge of the container around
the entire circumference.
Mount the assembled dust container to the vacuum cleaner.
The hitch near the latch of the bottom cover should hit the recess in the housing. Slide the top part of the container towards the
vacuum cleaner housing (IX), until the latch engages. You will hear the sound of the latch mechanism. A correctly installed con-
tainer cannot be removed otherwise than by pressing the container latch button.
Installation of accessories
Connect the hose to the air inlet of the dust container. Insert the hose connector into a round opening so that the tabs on the
connector slip into the gaps in the opening (X) and then turn the hose connector towards the locked padlock symbol. A correctly
installed hose connector fi ts the edge of the container opening around the entire circumference.
Disassemble the hose by turning the connector towards the padlock symbol and then slide it out of the dust container opening.
The pipe or a selected brush can be fi tted to the free end of the hose. Mounting is done by sliding the end of the hose into the
inside of the pipe or brush.
Using the appliance
After installing the dust container, hose and selected brush, connect the power cord plug to the socket. Grasp the plug and pull
out the cord to the length required for cleaning. A coloured marker (XI) is located at the end of the cord. When you see the marker,
stop pulling the cord out, otherwise the cord or the cord self-winding mechanism may be damaged.
Rolling up the excess power cord is carried out by pressing the cord winding button (XII). When winding, hold the cord in your hand
to prevent entanglement and impact of the plug on the vacuum cleaner housing.
After connecting the vacuum cleaner to the socket, press the switch and start vacuuming.
The vacuum cleaner is switched off after pressing the switch.
Purpose of the accessories
Flexible hose - used to connect the pipe or brush with the vacuum cleaner. The hose handle is equipped with a mechanical suction
power regulator. The more open the regulator cover, the lower the suction power.
Telescopic pipe - a pipe of adjustable length, which allows for comfortable selection of working height. The length is adjusted by
pushing and holding the locking button and then changing the length. Releasing the pressure on the button and then slightly pull-
ing the pipe will trigger the lock and set the length of the pipe, and the sound of the ratchet mechanism will be heard.
Metal pipe - allows for telescopic pipe extension.
Floor and carpet brush - universal brush for cleaning both carpets and all types of hard fl oors. The brush is equipped with a lever
that allows the bristles to be pushed in and out. Pressing the lever in place of the bristle brush symbol pushes the bristles out.
Pressing the lever in place of the brush symbol without bristles pushes the bristles in.
Small brush - allows you to clean where a larger brush cannot fi t.
2 in 1 crevice brush - allows for cleaning in narrow crevices. The brush is equipped with rotating bristles.

MAINTENANCE AND STORAGE

CAUTION! Never immerse the vacuum cleaner in water or other liquids. Doing so may result in electric shock.
After cleaning, turn off the vacuum cleaner with the switch, disconnect the power cord plug from the socket, retract the cable,
O R I G I N A L I N S T R U C T I O N S
14