Projector Function - miniland dreamcube magical Mode D'emploi

12. Micro-USB DC connector
13. Jack-jack 3.5 mm audio cable
5. INSTRUCTIONS FOR USE
5.1. DEVICE POWER SUPPLY
dreamcube can be plugged in, so parents don't have
to worry about battery life; or batteries can be used if
parents want to avoid using cords.
Follow these steps according to the power supply that
is chosen:
1. With the micro-USB cable that is included:
a. Connect the USB cable to the adapter and the
micro-USB end to the 'DC 5V' input on the device.
b. Plug in the adapter.
2. With batteries:
a. Open the battery compartment lid on the bottom
of the projector.
b. Insert batteries observing the polarity symbols
shown in the compartment.
c. Ensure the lid is properly closed.
5.2. FUNCTIONS
This projector with sounds and melodies will help
your baby to relax and fall asleep. Thanks to its sound
activation system, dreamcube will start automatically if
it detects that your baby is crying, and its relaxing lights
and sounds will soothe your baby.
The projector's functions and how to use them are
explained below.

5.2.1. PROJECTOR FUNCTION

To start the projection, press the projection on button
in the shape of a light bulb (1). The light will change
colour (green, red and blue), and will soothe and help
the baby to fall asleep.
The device includes three different and interchangeable
projection discs: a starry sky, under the sea and space.
Please note that the disc that is placed at the top of the
projector will be the one that is projected onto the wall.
To change the disc, just lift the tab you find round each
one of the discs, as you can see in Figure 2.
To switch the projection off, press the light bulb button
(1) again.
Note 1: Remove the protective plastic from the
projection discs before use Figure 3.
Note 2: Place the projection discs with the bright
side facing outwards.
5.2.2. MUSIC BOX FUNCTION
5.2.2.1. PLAYING PRELOADED SOUNDS
dreamcube includes 10 preloaded melodies and 5
sounds that have been specially selected to soothe and
relax babies. To activate them, press the button in the
shape of a musical note (2) or on the loop button (4).
To change the song or sound, press the selection button
(4) until you get the one you want. dreamcube repeats
the same song by default. If you want to play all the
melodies and repeat them, hold the selection button
(4) pressed for three seconds until the next song begins
to play. The projector will then play all the songs one
after another.
To go back to repeating the same song, press the
selection button (4) again.
The speaker volume can also be adjusted by pressing the
volume control button (3). There are 5 levels and you
can adjust the volume by pressing this button.
The sound turns off automatically after about 30
minutes. To turn it off before then, press the musical
note button again.
Note 1: If you turn the sound off, the device will
remember the last tune that was played and when you
turn it on again it will play that same tune.
Note 2: Only melodies, not sounds, will be played back
cyclically.
5.2.2.2. PLAYING OTHER SOUNDS
As well as playing preloaded melodies and sounds,
dreamcube can also play any other song from your
mobile phone, tablet or computer.
To do this, connect the jack-jack audio cable with the
3.5 mm connector that is supplied (13) to your mobile
device and the other end to the 'LINE IN' input on the
projector.
When you do this, press the musical note button (2)
to play the sounds on your dreamcube. Press the same
button again to stop it playing.
Note 1: In this case you have to adjust the volume via
your own mobile device.
Note 2: If the sound activation mode is off, the melodies
and projections can be used independently, so it will
be up to users to use one or the other according to
their needs.
5.2.3. SOUND ACTIVATION
dreamcube has a sound activation function. If your baby
cries, it will switch on automatically and soothe the baby
with relaxing lights and sounds. To turn on this function,
press the sound activation on button (5).
If the device is already on, you will hear a double beep.
If the device is switched off, you will hear a single beep.
Both indicate that the sound activation mode has been
turned on.
9
ENGLISH