Vision CS-1900 Manuel Du Produit page 4

Warnings
For electronic products
Caution – risk of electric shock. Do not open.
Use only domestic AC outlets. Connecting to an outlet supplying a higher voltage may create a fire hazard. Do not disconnect
the plug from the AC outlet by pulling the cord; always pull the plug itself. If you do not intend to use the product for any
considerable length of time, unplug the unit. Ensure power cable is not twisted, squeezed, or sheared.
Do not install this product in a location exposed to direct sunlight or close to heating equipment, extremely cold locations,
places subject to excessive vibration or dust, and or poorly ventilated places. Do not expose this appliance to excessive
humidity, rain, moisture, dripping, or splashing. Do not place objects filled with liquids on or near this product.
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect the interconnection cords with
other units. If you detect an abnormal smell or smoke, turn this product off immediately and unplug the power cord. Contact
your reseller or Vision.
For motorised products
• This product uses a very powerful motor to lift heavy displays. Read and understand this manual before installation.
• Failure to comply with the safety and installation instructions may cause serious bodily injury.
• This stand should only be operated by users over 18 years old.
• The stand should not be operated by persons under the influence of alcohol or recreational drugs
• Use the correct safety equipment AND adhere to workplace health and safety laws
• The SWL (safe working load) for this product is available on VISION'S website
• Ensure it is installed in an appropriate place – for example not obstructing an emergency exit.
• Check stability after installation. Ensure display is clipped into place securely.
• Installation must be done by a specialist audio-visual installer
• Allow 500mm x 500mm space around the floor stand.
• Avoid installing in a moist environment, or in direct sunshine, or near corrosive gas or liquid.
• Routing of cables through the bracket must comply with local regulations.
• Use a memory position to set the upper limit, to prevent the display going into ceiling.
Use extreme care lowering stand. Keep obstacles well clear. The stand might crush a person, or the display could become
dislodged and fall on a person. Serious injury may occur. If left unattended the control should be left out of reach of children.
For wireless and bluetooth products
Never use this product near an aircraft or medical facility. It can cause interference. Use of product in the following locations
may result in abnormal video/audio output:
• Product installed in walls made of concrete
• Product situated near refrigerator, microwave oven or other metal items
• A cluttered room where the wireless signals may be blocked
This product has been tested and manufactured to comply with each country's safety rules, however there is no guarantee
that interference will not occur in some scenarios. If interference happens, adjust distance between transmitter and receiver.
This product may interfere 5GHz wireless devices. If interference occurs configure your 5GHz router to 2.4 GHz band only.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. This equipment generates, uses and can radiate radio frequency energy and may in extreme cases cause harmful
interference to radio communications. If this happens the user should try:
• Relocating the receiving antenna
• Increasing the separation between the equipment and receiver
• Connect the equipment to a different power circuit.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body.
6
PRODUKTVEJLEDNING CS-1900
DA
1 Markér udskæringshullet
Bemærk: Hvis loftet er lavet med loftsplader, skal du fjerne
pladen og gøre det på gulvniveau.
Brug en udskæringsskabelon til at markere højttalernes
placering. Sørg for, at der ikke er nogen struktur umiddelbart
over den planlagte placering.
2 Udskæringshul
Bor pilothullet indenfor linjen. Skær forsigtigt.
3 Træk højttalerkablet
Læg kablet til højttaleren
4 Tilslut højttalerne
Rød er +, sort er -
Tilslutning af to som vist udgør en belastning på 8 ohm
Tilslutning af fire vil udgøre en belastning på 4 ohm
Forstærker
VENSTRE HØJRE
Tryk på terminalstikkene, og indsæt kablet.
5 Gør klar til installation
Sørg for, at klemmerne drejes ind som vist.
7