Important Safety Instructions - Tylo tx202/w Instructions De Montage

Table des Matières

Publicité

200-208 V~
Type Tonic (2.2 kW)
Amp
200 - 208 - 230 - 240 V~
11
1 = Tonic
200-208 V~
Type Tonic (4.5 kW)
Amp mm
200 - 208 - 230 - 240 V~
23
1 = Tonic
Type Tonic (4.5 kW)
Amp
400 - 415 V 2N~
10
1 = Tonic
N B B
200-240V~
Lighting
IMPORTANT SAFETY
INSTRUCTIONS
1. READ AND FOLLOW
ALL INSTRUCTIONS.
2. WARNING
injury, do not permit children to use this product
unless they are closely supervised at all times.
3. WARNING
injury:
a. The wet surfaces of steam enclosures may be
slippery. Use care when entering or leaving.
b. The steam head is hot. Do not touch the steam
head and avoid the steam near the steam head.
c. Prolonged use of the steam system can raise
excessively the internal human body temperature
and impair the body's ability to regulate its internal
temperature (hyperthermia). Limit your use of
steam to 10 – 15 minutes until you are certain of
your body's reaction.
d. Excessive temperatures have a high potential
for causing fetal damage during the early months
of pregnancy. Pregnant or possibly pregnant
women should consult a physician regarding
correct exposure.
e. Obese persons and persons with a history of
heart disease, low or high blood pressure,
circulatory system problems or diabetes should
consult a physician before using a steambath.
f. Persons using medication should consult a
physician before using a steambath since some
medication may induce drowsiness while other
medications may affect heart rate, blood pressure
and circulation.
1
G
230-240 V~
2
2
mm
Amp
mm
Awg
A
B
C
D
2.5
10
1.5
14
200-240 V~
1
G
230-240 V~
2
2
Amp
mm
Awg
A
B
C
D
6
20
4
12
200-240 V~
1
G
A
B
C
D
mm
2
Awg
1.5
14
L1 L2
N
400-415 V 2N~
– To reduce the risk of
– To reduce the risk of
4. SAVE THESE
INSTRUCTIONS.
Trouble-shooting
WARNING! ELECTRICAL WORK MUST BE CARRIED OUT BY A
QUALIFIED ELECTRICIAN!
WARNING! BEFORE CARRYING OUT ANY WORK ON THE UNIT
MAKE SURE THAT THE EQUIPMENT IS DISCONNECTED FROM
THE POWER SUPPLY!
In the event of a malfunction, first check the following:
• Is Tonic correctly wired up in accordance with the wiring diagram?
• Is the water filter clean? The filter is located adjacent to the water feed. When
cleaning, loosen the pipe connection, remove the filter and clean off any calcium
deposits or foreign bodies.
• If there is any form of shut-off valve on the pipe leading to the steam generator,
make sure that this is in the open position.
• Are all the fuses in the fuse box intact?
• Is the control panel correctly set?
• Make sure that the integral temperature limit control has not been activated.
How to enjoy your steam bath to the full!
For most people 40-45°C is usually a suitable bathing temperature. You can set
the temperature and read it directly on the control panel. (There is no need for a
hygrometer; the relative humidity is always 100%).
• Shower and wash well before starting your steam bath.
• Take a towel to sit on.
• Relax and let yourself unwind in the clouds of soothing steam.
• Cool off now and again with an invigorating shower. Alternate between the
steam bath and shower functions as many times as you wish.
• Round off your last session amid the clouds of steam with a cool, refreshing
shower.
Let your skin dry slowly in the warm air before dressing. Sit without clothes until your
skin has cooled down and the pores have closed. Treat yourself to a long, cool drink,
relax and enjoy the feelgood factor!
In the event of any problems, please contact the retailer where you
purchased the equipment.
© The contents of this publication may not be reproduced in part or in whole without the written permission of
Tylö. Tylö reserves the right to amend specifications of materials, construction and design.
9

Publicité

Table des Matières
loading

Table des Matières