Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
CFB6FFDIVKIT FURNITURE FEED DIVIDER KIT
6 GANG RECESSED CONCRETE FLOOR BOX
Installation Instructions
CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing.
NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes,
communications standards, the following instructions and any instructions included with individual devices.
NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance with the NEC
and CE Code requirements.
Use with CFB6G30 series floor boxes and 610GCFFCVR or 610GTFFCVR series covers.
See 610GCFFCVR and 610GTFFCVR series cover installation instructions to install cover.
1.
Remove temporary concrete cover, pull and dress wires as per 610GCFFCVR and 610GTFFCVR series cover installation
instructions.
2.
Retain cover partition components [8] for installation to cover. Refer to 610GCFFCVR and 610GTFFCVR series cover
installation instructions.
3.
For multi service applications, wireway [1] and dividers [2] must be installed or must be purchased separately if
missing, see FIGURE A.
4.
Feed thru capacity only from side to side thru wiring chambers, see CONFIGURATION. Dividers [3] can be removed as
needed. See FIGURE A.
1 INCH FEED WIRING CHAMBER
2
SIDE
END
SIDE
2 INCH FEED WIRING CHAMBER
CONFIGURATION
Wiring Device - Kellems
Hubbell Incorporated (Delaware)
Shelton, CT 06484
1-800-288-6000
www.hubbell-wiring.com
PD2929
02/21
2
1
END
3
SIDE
3
SIDE
END
FIGURE
A
2
8
ENGLISH
3
3
END
2
Publicité
Manuels Connexes pour Hubbell CFB6FFDIVKIT
Sommaire des Matières pour Hubbell CFB6FFDIVKIT
- Page 1 CFB6FFDIVKIT FURNITURE FEED DIVIDER KIT 6 GANG RECESSED CONCRETE FLOOR BOX Installation Instructions ENGLISH CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing. NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes, communications standards, the following instructions and any instructions included with individual devices.
- Page 2 Align and install spacer [4] as shown in FIGURE B. Torque screw [5] to 9-12 lbs -in (1.0 - 1.3 N m), see FIGURE E. Torque screw [5] to 9-12 lbs -in (1.0 - 1.3 N m), see FIGURE B. After dividers [6] and [7] are installed, check the gap between divider [6] &...
- Page 3 ENSEMBLE DE CLOISONS CFB6FFDIVKIT POUR BO TE DE PLANCHER EN B TON ENCASTR E 6 COMPARTIMENTS DESTIN E L ALIMENTATION DU MOBILIER Directives de montage FRAN AIS ATTENTION - RISQUE DE CHOC LECTRIQUE. D brancher le circuit avant de proc der au montage ou la maintenance.
- Page 4 Aligner et installer la cloison [4] conform ment l'illustration de la FIGURE B. Serrer la vis [5] un couple de 1,0 - 1,3 Nm (9-12 lbpo), consulter la FIGURE E. Serrer la vis [5] un couple de 1,0 - 1,3 Nm (9-12 lbpo), consulter la FIGURE B. Une fois les cloisons [6] et [7] install es, v rifier le jeu entre la cloison [6] et la cale [4] puis entre la cloison [7] et la Visser la vis (5) de mani re engager les filets, consulter la FIGURE C.
- Page 5 Hubbell Products M xico, S. de R.L. de C.V. garantiza este producto, de estar libre de defectos en materiales y mano de obra por un a o a partir de su compra.
- Page 6 Alinee e instale el espaciador [4] como se muestra en la FIGURA B. Apriete el tornillo [5] a un par de 9-12 lbs-in (1.0 - 1.3 N m), vea la FIGURA E. Apriete el tornillo [5] a un par de 9-12 lbs-in (1.0 - 1.3 N m), vea la FIGURA B. Despu s de instalar los divisores [6] y [7], verifique el espacio entre el divisor [6] y el espaciador [4] y entre el divisor Instale el tornillo [5] lo suficiente como para enganchar las roscas, vea la FIGURA C.