Honeywell CT54 Instructions D'installation
Honeywell CT54 Instructions D'installation

Honeywell CT54 Instructions D'installation

Masquer les pouces Voir aussi pour CT54:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

STEP 1. PREPARE FOR
INSTALLATION
The CT54 Thermostat controls 2-wire, 15 Vac to 30 Vac,
gas, oil or electric heating-only systems.
The CT54 Thermostat is not suitable for:
• cooling systems
• heating-cooling systems
• 3-wire electric heating systems
If you are unsure which thermostat model is right for your
system, visit www.honeywell.com/yourhome or call
Honeywell Customer Care at 1-800-468-1502.
1. Check that the following components are included:
• Thermostat
• Two one-inch screws
• Installation Instructions
2. Required tools:
• Slotted screwdriver
• Drill
• Drill bit (1/16 in.)
• Needle nose pliers
• Level
• Pencil
STEP 2. REMOVE OLD
THERMOSTAT
1. Turn power off to the system at the furnace or at
the fuse/circuit breaker panel.
2. If the cover does not easily pull off, remove any
screws that may fasten the cover to the thermostat.
® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc. •
CT54 Thermostat
3. Locate the heat anticipator scale and the heat
anticipator lever on the old thermostat (see Fig. 1).
TYPICAL LOCATION OF HEAT
ANTICIPATOR SCALE AND LEVER
Fig. 1. Heat anticipator on old thermostat (example).
4. Record the number that the heat
anticipator lever points to on the heat
anticipator scale.
NOTE: If you cannot find the heat anticipator setting on
your thermostat, you can use a standard setting
for your type of system when you reach Step 5.
Set Heat Anticipator On New Thermostat.
5. Remove the screw or screws that hold the thermo-
stat to the wall and pull the thermostat away from
the wall.
6. Remove the two wires from the old thermostat and
wrap them around a pencil to keep them from fall-
ing back into the wall (see Fig. 2). If there are more
than two wires connected to your old thermostat,
do not remove the wires. Visit www.honey-
well.com/yourhome or call 1-800-468-1502 for fur-
ther assistance with the installation.
Fig. 2. Pull wires through wall opening.
• All Rights Reserved
INSTALLATION INSTRUCTIONS
OLD THERMOSTAT HEAT
ANTICIPATOR SCALE
HEAT ANTICIPATOR LEVER
WIRES
THROUGH
WALL
OPENING
M19645
M21192
69-1696EF

Publicité

Table des Matières
loading

Sommaire des Matières pour Honeywell CT54

  • Page 1 TYPICAL LOCATION OF HEAT ANTICIPATOR SCALE AND LEVER M21192 The CT54 Thermostat controls 2-wire, 15 Vac to 30 Vac, Fig. 1. Heat anticipator on old thermostat (example). gas, oil or electric heating-only systems. 4. Record the number that the heat...
  • Page 2 CT54 THERMOSTAT MERCURY NOTICE If this thermostat is replacing a control that contains mercury in a sealed tube, do not place the old thermostat in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal of this control or of an old control containing mercury in a sealed tube.
  • Page 3: If You Have A Problem

    CT54 THERMOSTAT STEP 5. SET HEAT ANTICIPATOR STEP 6. OPERATING NEW ON NEW THERMOSTAT THERMOSTAT 1. Set the heat anticipator lever to the number that 1. Adjust the temperature setting lever to your desired you recorded in Step 2. Remove Old Thermostat, setting.
  • Page 4 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 Printed in U.S.A. on recycled 69-1696EF J.S. 9-03 www.honeywell.com/yourhome paper containing at least 10% post-consumer paper fibers.
  • Page 5: Étape 1. Avant L'installation

    Le thermostat CT54 sert à commander des systèmes de chauffage seulement, bifilaires, de 15 à 30 V c.a., au gaz, au mazout ou à l’électricité. Le thermostat CT54 ne convient pas à ce qui suit : ÉCHELLE DE LA RÉSISTANCE ANTICIPATRICE • systèmes de refroidissement DE CHALEUR DE L'ANCIEN THERMOSTAT •...
  • Page 6: Étape 3. Raccordement Des Fils Au Nouveau Thermostat

    THERMOSTAT CT54 FILS À TRAVERS L'OUVERTURE DANS LE MUR MF19645 Fig. 2. Faire passer les fils par l’ouverture dans le mur. AVIS DE RECYCLAGE Si le nouveau thermostat remplace un ancien régulateur contenant un contact à mercure, ne M19647 pas mettre l’ancien régulateur aux poubelles.
  • Page 7: Étape 6. Fonctionnement Du Nouveau Thermostat

    Pour obtenir d’autres renseignements, consultez le site www.honeywell.com/yourhome ou composer le numéro Eau chaude d’assistance sans frais de Honeywell : 1-800-468-1502. Système à air chaud à haut rendement (90 % ou plus) Avant de composer, assurez-vous d’avoir en main l’information suivante : Gaz ou mazout Air chaud •...
  • Page 8 Solutions de régulation et d'automatisation Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35, Dynamic Drive Golden Valley, MN 55422 Scarborough (Ontario) M1V 4Z9 Imprimé aux États-Unis sur du papier 69-1696EF J.S. 9-03 www.honeywell.com recyclé contenant au moins 10 %...

Table des Matières