Halo L805 Serie Instructions D'installation

HALO
Installation Instructions for L805/806/807, LJ805/806/807
LL805/806/807
•
Wear rubber-soled shoes and work on a sturdy ladder.
•
This fixture must be installed according to the National Electric Code and local building
codes.
•
To avoid a hazard to children, account for all parts and destroy all packing materials.
•
To reduce the risk of fire and electrical shock, use only fixtures and fittings intended
for use with "LF", "LA", "L", "LJ" and "LL" series track.
•
Do not install in damp or wet locations.
•
Do not install luminaire assembly closer than 6 inches from any curtain or similar
combustible material.
•
Read carefully for your protection and save all instructions.
Service
For service questions contact point of purchase.
Installation Instructions for Halo Flexible Track ('LF' Series)
To Install Unit on Track (Fig 1):
Step 1.
Open CONNECTOR COVER by pulling downward on the CONNECTOR SLEEVE and
raising CONNECTOR COVER (Fig. 1).
Step 2.
Hang unit on the TRACK so the CONTACTS are facing the intended circuit. 120V units
have 2 circuit options. 12V version has 1 circuit.
Note:
For 120V Units - To access the other circuit, rotate the unit 180°.
Step 3.
Move CONNECTOR into position and close CONNECTOR COVER until it snaps into
position.
To Remove Unit from Track:
Note:
Allow unit to cool before removing from the track.
Step 1.
Open CONNECTOR COVER by pulling downward on the CONNECTOR SLEEVE and
raising CONNECTOR COVER.
Step 2.
Remove unit from track.
Installation Instructions for Halo Power-Trac ('L' Series), Lazer Track ('LZR' Series), Juno Track ('LJ' Series) and
Lightolier Track ('LL' series)
To Adjust Adapter (Fig 2A & 2B):
'L' units can be used with Lazer Track, Halo Single Circuit
Trac and Halo-2 Two Circuit Trac. 'LJ' units can be used
with Juno T Single Circuit and TU two circuit Trac. 'LL'
units can be used with Lightolier Lytespan Single Circuit
6000 series and two circuit Trac 6100 series. An
adjustable contact allows you to select circuit position.
Use a narrow blade screwdriver to adjust the contact. Lift
or lower the contact until it touches the plastic stop of the
contact assembly.
For Lazer, Halo Single Circuit and circuit #1 of Halo-2, 'L'-
track contact must be in down position (Fig. 2A). For
Halo-2 circuit #2, move contact to up position (Fig. 2B).
'LJ'- For Juno T single circuit and circuit #1 of TU, track
contact must be in down position (Fig. 2C). For Juno TU -
2 circuit #2, move contact to up position (Fig. 2D).
'LL'- For Lightolier Lytespan 6000 single circuit and circuit
#1 of Lytespan 6100, track contact must be in down posi-
tion (Fig. 2E). For Juno TU - 2 circuit #2, move contact to
up position (Fig. 2F).
2
, LF805 and LA805 Series Fixtures
FIG. 2A
CIRCUIT NO. 1
(DOWN)
FIG. 2C
CIRCUIT NO. 1
(DOWN)
FIG. 2E
CIRCUIT NO. 1
(DOWN)
1. Juno
2. Lightolier
Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX 770.486.4801
Risk of Fire/Electric
R
Shock
If not qualified, consult an
electrician.
Risk of Electric Shock
Disconnect power at fuse
or circuit breaker before
installing or servicing.
®
T single circuit and 2 circuit track contact. Juno is a registered trademark of Juno Lighting.
®
Lytespan 6000 single circuit and 2 circuit track contact. Lightolier is a registered trademark of Philips Lighting.
´L´ Connectors
1
,
Keep away from flammable
vapors or materials.
Risk of Burn
Disconnect power and
allow fixture to cool
before handling fixture.
FIG. 1
CONNECTOR
COVER
120V Units
CONTACTS
CONNECTOR
SLEEVE
FIG. 2B
CIRCUIT NO. 2
(UP)
FIG. 2D
CIRCUIT NO. 2
(UP)
FIG. 2F
CIRCUIT NO. 2
(UP)
CLP-0001288-rev2
page 1
TRACK
704732INS