Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Always wear SAFETY GLASSES
when installing hitch
Access
hole
5
B. Align block on
C. Pull bolt
A. Insert bolt and
access hole
Block into frame
Figure 1
1.
Lower exhaust– Using an exhaust hanger removal tool, lower muffler by removing (4) rearmost rubber hanger for two exhaust mufflers and (1) forward rubber hanger. A spray
of lubricant or soapy water on rubber hangers makes them slide off metal pins more easily. NOTE: Be sure that exhaust is properly supported before removing rubber
hangers.
2.
Using a flat head screwdriver, remove (5) rivets from bottom of fascia and keep for reinstallation.
3.
Feed the carriage bolts ① and spacers ② through access holes on both side frame rails using the pull wires ⑨ for horizontal holes, see Figure 1. Leave pull wires attached.
4.
Trim lower fascia – Using a tape measure, marker, and utility knife, measure, mark, and trim the lower fascia. See Figure 2.
fascia prior to trimming. Dimensions are approximate.
5.
Install Hitch - Raise hitch into position, over the exhaust, and feed the pull wires through bracket slots. Remove pull wires and loosely install conical washers ③, hex nuts ④
to the hitch. Loosely install carriage bolt ⑤, spacer ⑥, conical washer ⑦, hex nut ⑧ through hook bracket of hitch and vehicle tow hook, see Figure 3 & 4.
6.
Tighten all 7/16-14x1.25 GR 5 fasteners to 50 ft-lb (68 N*m) and 1/2-13x2.00 GR 5 fastener to 75 ft-lb (102 N*m).
7.
Reinstall (4) rivets on bottom of fascia and return (1) rivet to owner and reinstall the muffler hanger to move the muffler back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged
should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for
connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2022 Horizon Global Americas Inc. - Printed in Mexico
Installation Instructions
PART NUMBERS: 76342, 84342, CQT76342
Fasteners typical
on both sides
6
7
8
4
Figure 3
thru block
5
Hook
6
Bracket
of hitch
1
Vehicle Tow
2
Hook
Figure 4
3
Conical Washer
Teeth side
Against hitch
Sheet 3 of 18
Fastener Kit: 76342F
①
Qty. (4)
Carriage Bolt
7/16"-14 x 1.25 GR5
②
Qty. (4)
Spacer .188x1.00x2.00
③
Qty. (4)
Washer Conical 7/16''
7
8
Qty. (4)
Hex nut
4
7/16 GR2
Qty. (1)
Carriage Bolt
5
1/2-13x2.00 GR 5
Qty. (1)
Spacer .250x1.50x3.00
6
Qty. (1)
Washer Conical 1/2''
7
Qty. (1)
Hex Nut
8
1/2 GR5
9
Qty. (4)
Pull wire 7/16-14
"
"
��
��
C C
C
of Vehicle
of Vehicle
of Vehicle
L L
L
Figure 2
Check for sensors and or wiring on the inside of the
Proper torque is needed to keep the hitch
secure to the vehicle when towing.
76342NP
06-24-22
��
��
��
��
"
"
��
��
Rev. C
Publicité
Table des Matières
