Ariens 9602032 24 Manuel Du Propriétaire
  1. Manuels
  2. Marques
  3. Ariens Manuels
  4. Tondeuses à gazon
  5. 9602032 24
  6. Manuel du propriétaire
Ariens 9602032 24 Manuel Du Propriétaire

Ariens 9602032 24 Manuel Du Propriétaire

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
FRONT TINE TILLER
Owners Manual
Models
9602032 24" FRONT TINE TILLER
Gasoline containing up to 10% ethanol (E10) or up to 10% MTBE (methyl tertiary butyl
ether) is acceptable for use in this machine. The use of any gasoline exceeding 10%
ethanol (E10) or 10% MTBE will void the product warranty.
ENGLISH
431714 Rev. 1 (21547634) 06.06.11
Printed in USA

Publicité

Table des Matières
loading

Manuels Connexes pour Ariens 9602032 24

Sommaire des Matières pour Ariens 9602032 24

  • Page 1 FRONT TINE TILLER Owners Manual Models 9602032 24" FRONT TINE TILLER Gasoline containing up to 10% ethanol (E10) or up to 10% MTBE (methyl tertiary butyl ether) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) or 10% MTBE will void the product warranty.

  • Page 2: Preparation

    SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers TRAINING • Keep children and pets away. • Read the Owner’s Manual care ful ly. Be thor ough ly • Do not overload the machine capacity by attempting fa mil iar with the controls and the proper use of the to till too deep at too fast a rate.

  • Page 3: Table Des Matières

    PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for Gasoline Capacity: 3.6 Quarts (3.4L) and using your tiller. Unleaded Regular • Follow instructions under “Maintenance” and “Stor age” Oil (API-SG-SL): SAE 10w-30(Above 32°F/0°C) sections of this Manual.

  • Page 4: Assembly

    ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary ensure proper tightness.

  • Page 5: Handle Height

    ASSEMBLY UNPACK CARTON & INSTALL HANDLE INSTALL DEPTH STAKE AS SEM BLY (See Fig. 2) (See Fig. 3) • Loosen nut “A”. CAUTION: Be careful of exposed • Insert stake support between engine brack et halves sta ples when handling or disposing with stake spring down.

  • Page 6: Operation

    OPERATION KNOW YOUR TILLER READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. FORWARD TINE CONTROL CHOKE CONTROL THROTTLE CONTROL...
  • Page 7 OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses.

  • Page 8: Before Starting Engine

    OPERATION TO TRANSPORT ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. CAUTION: Before lifting or trans port ing, Use fresh, clean, regular un lead ed gasoline with a allow tiller engine and muffler to cool. minimum of 87 octane.
  • Page 9 OPERATION • Soil conditions are important for proper tilling. Tines will 6. After starting the engine, gradually open choke by not readily penetrate dry, hard soil which may con trib ute turning the choke lever and finally keep it fully opened. Do not fully open the choke lever immediately when to excessive bounce and difficult handling of your tiller.

  • Page 10: Maintenance

    MAINTENANCE GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this tiller does not cover items that have TINE CON TROL been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main tain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller.

  • Page 11: Engine Lubrication

    MAINTENANCE Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance.

  • Page 12: Spark Plug

    MAINTENANCE SPARK PLUG COOLING SYSTEM (See Fig. 14) Replace spark plugs at the beginning of each tilling sea- Your engine is air cooled. For proper en gine performance son or after every 50 hours of use, whichever comes first. and long life keep your engine clean. Spark plug type and gap setting are shown in “PROD UCT •...

  • Page 13: Service & Adjustments

    SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. MID-WIDTH TILLING - 22" PATH (See Fig. 17) TILLER • Assemble holes “A” in tine hubs to holes “C” in tine shaft.
  • Page 14 SERVICE AND ADJUSTMENTS TINE OPERATION CHECK (See Fig.19) TO REMOVE BELT GUARD (See Fig. 20) • Remove screws from side of belt guard. WARNING: Disconnect spark plug wire • Pull belt guard out and away from unit. from spark plug to prevent starting while checking tine operation.
  • Page 15 SERVICE AND ADJUSTMENTS ENGINE BELT REPLACEMENT • Install new V-belt to engine pulley first then to trans mis- TO AD JUST CARBURETOR sion pulley. Ensure belt is positioned on inside groove of both pulleys, inside all belt guides and rests on idler The carburetor has been preset at the factory and ad just ment pulley.

  • Page 16: Storage

    STORAGE Immediately prepare your tiller for storage at the end of the ENGINE OIL season or if the unit will not be used for 30 days or more. Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual.) WARNING: Never store the tiller with gasoline in the tank inside a build ing where fumes may reach an open flame...

  • Page 17: Troubleshooting

    TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start Out of fuel. Fill fuel tank. Engine not “CHOKED” properly. See “TO START ENGINE” in the Operation section. Engine flooded. Wait several minutes before attempting to start. Dirty air cleaner. Clean or replace air cleaner cartridge. Water in fuel.
  • Page 18 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) HANDLE ASSEMBLY FT-handle_assy_2_r1...

  • Page 19: Handle Assembly

    FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) HANDLE ASSEMBLY ITEM MFG. ARIENS PART NO. DESCRIPTION 137176 21546089 Bracket, Handle 72140512 21546771 Bolt, Carriage 5/16-18 x 1-1/2 165787 21546171 Grip, Handle 166376 21546175 Handle, L.H. 73680500 21546784...
  • Page 20 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) BELT GUARD AND PULLEY ASSEMBLY...
  • Page 21 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) BELT GUARD AND PULLEY ASSEMBLY ITEM MFG. ARIENS PART NO. DESCRIPTION 23230506 21546545 Screw Set 5/16-18 x 3/8 Patch 130812 21546079 Sheave, Engine 86777 21546830 Screw, Tap Hex Head...
  • Page 22 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) WHEEL AND DEPTH STAKE ASSEMBLY...
  • Page 23 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) WHEEL AND DEPTH STAKE ASSEMBLY ITEM MFG. ARIENS PART NO. DESCRIPTION 9194R 21546837 Pin, Clevis 74760520 21546806 Bolt, Hex Head 5/16-18 x 1-1/4 74760512 21546804 Bolt, Hex Head 5/16-18 x 3/4...
  • Page 24 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) TINE ASSEMBLY...
  • Page 25 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) TINE ASSEMBLY ITEM MFG. ARIENS PART NO. DESCRIPTION 156926 21546140 Tine, Outer, R.H. 3146R 21546548 Retainer, Spring 156924 21546138 Tine, Inner, R.H. 156923 21546137 Tine, Inner, L.H. 156925 21546139 Tine, Outer, L.H.
  • Page 26 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) TRANSMISSION...
  • Page 27 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) TRANSMISSION ITEM MFG. ARIENS PART NO. DESCRIPTION 74760524 21546807 Bolt, Hex Head, Gr. 25/16-18 x 1-1/2 74780652 21546817 Bolt, Hex Head, 3/8-16 x 3-1/4 19131311 21546282 Washer 13/32 x 13/16 x 11 Ga.
  • Page 28 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) DECALS...
  • Page 29 FRONT TINE TILLER – MODEL NUMBER 90203200 (MFG. ID. NO. 96086000101) DECALS ITEM MFG. ARIENS PART NO. DESCRIPTION 431744 21547632 Decal, Console 431742 21547845 Decal, Belt Guard 110613X 21546047 Decal, Tine Control 423701 21546713 Decal, Subaru Tine Shield 110614X 21546048...

  • Page 30: Customer Responsibilities

    For the next 12 months, Ariens will cover the pro- rated cost of replacing a battery pack and/or battery subassembly that fails due to defect in material or workmanship.

  • Page 31: Parts

    Canada. In all other countries, contact place of purchase for warranty information. Disclaimer Ariens may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating Ariens to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.

  • Page 32: Parts And Service

    For parts and service, contact your local Ariens dealer. To find a dealer in your area, call 1-877-257-6920, or use the Dealer Locator on our web site, www.ariens.com.

Table des Matières