Safety Instructions And Warnings; Technical Safety; Electrical Safety - FALMEC Vittorio FIVIT34B6SS Mode D'emploi

SAFETY INSTRUCTIONS
AND WARNINGS
READ AND SAVE THESE INSTRUCTIONS
Installation operations are to be carried
out by skilled and qualified installers in
accordance with the instructions in this booklet
and in compliance with the regulations in force.
DO NOT use the hood if the power supply cable or
other components are damaged: disconnect the
hood from the electrical power supply and contact
the Dealer or an authorised Servicing Dealer for
repairs.
Do not modify the electrical, mechanical or func-
tional structure of the equipment.
Do not personally try to carry out repairs or
replacements. Interventions carried out by
incompetent and unauthorised persons can
cause serious damage to the unit or physical and
personal harm, not covered by the Manufacturer's
warranty.
WARNING: TO REDUCE THE RISK OF FIRE, ELEC-
TRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by
the manufacturer. If you have questions, contact
the manufacturer.
b) Before servicing or cleaning unit, switch pow-
er off at service panel and lock the service dis-
connecting means to prevent power from being
switched on accidentally.
When the service disconnecting means cannot
be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do
Not Use To Exhaust Hazardous Or Explosive Ma-
terials And Vapors.
WARNINGS FOR THE INSTALLER

TECHNICAL SAFETY

Before installing the hood, check the
integrity and function of each part. Should
anomalies be noted, do not proceed with
installation and contact the Dealer.
Do NOT install the hood if an aesthetic (or cos-
metic) defect has been detected. Put it back into
its original package and contact the dealer.
No claim can be made for aesthetic (or cosmetic)
defects once it has been installed.
During installation, always use personal protective
equipment (e.g.: Safety shoes) and adopt prudent
and proper conduct.
The installation kit (screws and plugs) supplied with
the hood is only to be used on masonry walls: in case
of installation on walls of a different material, assess
other installation options keeping in mind the type of
wall surface and the weight of the hood.
Keep in mind that installations with different types of
fastening systems from those supplied, or which are
not compliant, can cause electrical and mechanical
seal danger.
Do not install the hood outdoors and do not expose
it to atmospheric elements (rain, wind, etc.).
All set screws must be checked, and retightened
where necessary, before installation.
CAUTION: To Reduce The Risk Of Fire And Electric
Shock, Install This Rangehood Only With Remote
Blower Or Integral Blowers Manufactured by FAL-
MEC S.p.A. Models "Remote in-roof Blower".

ELECTRICAL SAFETY

The installation has to be in accordance with the
National Electrical Code, ANSI/NFPA 70 and local
codes. Making sure the power is off before at-
tempting installation.
The electrical system to which the hood is
to be connected must be in accordance
with local standards and supplied with earthed
connection in compliance with safety regulations
in the country of use. It must also comply with Eu-
ropean standards regarding radio antistatic prop-
erties.
WARNING: GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire
for the electric current. This appliance is equipped
with a cord having a grounding wire with a
grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk
of electric shock. Consult a qualified electrician if
the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not use an extension cord. If the power supply
cord is too short, have a qualified electrician in-
stall an outlet near the appliance.
Before installing the hood, check that the electrical
mains power supply corresponds with what is report-
ed on the identification plate located inside the hood.
9