Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Always wear SAFETY GLASSES
when installing hitch
End panel opening
Fasteners
typical
both sides
Conical Washer
Teeth side
Against hitch
1.
Loosen wheel well trim and liner – Using a Phillips screwdriver or 8 mm socket remove (4) screws at the bottom of wheel well liner per side. Gently loosen the wheel well trim on the
wheel well liner up to the edge of fascia. Using a T20 torxbit remove (1) screw inside the wheel well liner per side. Using a 10 mm socket remove (1) bolt behind wheel well trim per side.
2.
Remove taillight panel and taillight – Open tail gate. Using a plastic trim tool remove (1) taillight panel per side. Using a T27 torxbit remove (1) screw on each taillight. Gently remove
the taillight and carefully remove the electric harness while removing the taillight.
3.
Remove fascia – Twist the knobs on the panel door to unlock, gently pull and remove the panel door. Using 10 mm socket remove (4) bolts at the bottom of fascia. Open tail gate. Using
a plastic trim tool remove a cap near trunk weatherstrip at bottom corner per side. Using a 10 mm socket remove (1) bolt behind the cap per side. Use plastic trim tools to remove the
fascia starting at the outer edges near the wheel wells and gently pull the fascia. Carefully disconnect wiring harness male part on both sides (if present) while removing the fascia.
4.
Lower vehicle exhaust - Grand Cherokee L - Using 13 mm socket remove (3) bolts from two rearmost exhaust hangers per side to lower the exhaust.
Grand Cherokee - Using 13 mm socket remove one bolt from exhaust hanger per side to lower the exhaust. Save factory M8 bolt for reinstall. Note: Be sure that exhaust is properly
supported before removing exhaust hangers.
5.
Remove Bumper Beam – Using 21 mm socket remove (3) bolts from bumper beam per side. Remove bumper beam. Return fasteners and bumper beam to owner. NOTE: Access for the
recovery eye will be eliminated when bumper is removed, use the hitch safety chain openings for vehicle recovery situations.
6.
Install hitch – Grand Cherokee only - Install the M8 factory bolt as shown in Fig. 1, raise exhaust into position and install items
the hitch brackets though end panel opening into frame rails. Using pull wires ⑤ feed carriage bolts ① and spacers ② into the slots of hitch brackets through end panel opening and
then through the frame rail holes per side, see Fig. 1. Remove pull wires and loosely install conical washers ③ and hex nuts ④ to the frame rail, see Fig. 1.
7.
Tighten all fasteners with torque wrench 1/2" Gr8 to 110 ft.lb. (149 N*M) and M8 to 20 ft.lb. (27 N*M)
8.
Reinstall vehicle exhaust, fascia with wiring harness, panel door, all fasteners, taillight with electric harness
and fasteners, taillight panel, wheel well trim and liners.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be
removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2022 Horizon Global™ Corp - Printed in Mexico
Installation Instructions
PART NUMBERS: 76595, 84595, CQT76595
Frame rails
End panel
kl
Figure 1
NOTE: Inside of panel door may need to be trimmed to install 7-way electrical bracket.
j
k
l
m
Grand Cherokee Only
Factory M8 bolt
n
o
p
q
lm
lm
opq
Grand Cherokee Only
opq
onto factory M8 bolt, each side. Both - Slide in
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 3 of 27
76595NP
Fastener Kit: 76595F
Qty. (6)
Carriage bolt
1/2"-13x1.75" Gr8
Qty. (6)
Spacer .250"x1"x 2"
Qty. (6)
Conical washer 1/2"
Qty. (6)
Hex nut 1/2"-13
Qty. (6)
Wire pull 1/2"-13
Qty. (2)
Flat washer 5/16"
Qty. (2)
Lock washer 5/16"
Qty. (2)
Hex nut M8 x 1.25
⑤
Kink pullwire to keep spacer
independent of bolt
Figure 2
05/19/22
Rev. A
Publicité
Table des Matières
