Technical Data - Chicago Pneumatic CP8848 Serie Manuel De L'opérateur

EN
ENGLISH (ENGLISH)
1.

Technical Data

Drive Torque
Model
1 2
[ft.lbs]
[inch]
[Nm]
ah :Vibration level, k Uncertainty; L
Declaration of noise and vibration statement (EN60745)
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared values of other
tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured in individual work places
may be higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way the user works, the workpiece and the
workstation design, as well upon the exposure time and the physical condition of the user. We, CHICAGO PNEUMATIC TOOLS , cannot be held liable for the consequences
of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. This
tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at www. pneurop.eu/uploads/
documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf. We recommend a programme of health surveillance to detect early symptoms which may relate to noise or
vibration exposure, so that management procedures can be modified to help prevent future impairment.
2.
Machine type(s)
• This product is designed for installing and removing threaded fasteners in wood, metal and plastic. No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.
3.
Mounting instruction
• See figures.
4. Battery
• New battery packs reach full loading capacity after 4 - 5 charging and discharging. Battery packs which have not been used for some time should be rechar-
ged before use.
• Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
• The contacts of chargers and battery packs must be kept clean.
• For an optimum life-time, the battery packs have to be fully charged, after use.
5. Maintenance instruction
• Follow local country environmental regulations for safe handling and disposal of all components.
• Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised
dealer for advice on technical service or if you require spare parts.
• Disassemble and inspect the tool every three 3 months if the tool is used every day. Replace damaged or worn parts.
• Always ensure that the machine is disconnected from energy source to avoid accidental operation.
• High wear parts are underlined in the parts list.
• To keep downtime to a minimum, the following service kits are recommended :
Tune-up kit: see part list
6.
Disposal
• The disposal of this equipment must follow the legislation of the respective country.
• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
• Repair only by technical maintenance staff.
7. SYMBOL
Please read the instructions
carefully before starting the
machine.
Remove the battery pack
before starting any work on the
machine.
8.
EC Declaration of conformity
We : : CHICAGO PNEUMATIC Tool Co. LLC 1800 Overview Drive Rock Hill, SC 29730 - USA
Machine type(s) : impact wrench
Declare that the product(s) : CP8848
Origin of the product : Hungary
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to "Machinery" : (2006/42/EC), RoHs
(2011/65/EU), EMC (2014/30/EU), applicable harmonised standard(s) :
EN 60745-1:2009 + A11:2010 EN 60745-2-1:2010 EN 60745-2-2:2010
EN 55014-1:2006 + A1:2009 + A2:2011 EN 55014-2:1997 + A1:2001 + A2:2008
Name and position of issuer: Pascal Roussy (R&D Manager)
Saint-Herblain, 23/04/2016
Place & Date :
Technical file available from EU headquarter.
Copyright 2016, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings.
Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.
Original Instructions
Weight
Free speed Blows per minute
3 4
[lb]
min-1
[kg]
Sound pressure dB(A), K = K
pA pA
Do not dispose of electric tools together with household waste
material! In observance of European Directive on waste electrical
and electronic equipment and its implementation in accordance
with national law, electric tools that have reached the end of their
life must be collected separately and returned to an environmentally
compatible recycling facility.
Korean Conformity Mark
Serial Number: From 00001 to 99999
Pascal Roussy R&D manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
Dimension
Battery Voltage
LxWxH
W
L
5 6
[mm]
min-1
[inch]
= 3 dB Uncertainty
WA
CP8848 Series
Sound pressure
Sound power
L
pA
v
7 8
[volt] [dB(A)]
impact wrench
Vibrations
L
a
K
wA
hd
9 10
[dB(A)] [m/s²] [m/s²]
European
Conformity
Mark
EurAsian
Conformity
Mark.