Table des Matières
Publicité
1. DESCRIPTION DU PRODUIT ·································1-1
1.1. Vérification des piéces livrées ·······························1-1
1.2. Vérification du type et des spécifications ··············1-2
1.3.1. Convertisseur de débit (FSV..S(IP66) ············1-6
1.3.2. Convertisseur de débit (FSV..H(IP67) ············1-7
1.3.4. Capteur petite/moyenne taille (FSG) ··············1-8
1.3.5. Capteur grande taille (FSG)····························1-9
(FLD) ····················································1-10
DEMARRAGE DU DEBIMETRE·····················2-1
2.1. Procédure d'installation ·········································2-1
3. INSTALLATION ·······················································2-2
3.2. Emplacement et installation du capteur ················2-3
3.2.1. Longueur de ligne droite du tuyau ··················2-4
3.2.2. Position de montage ·······································2-5
3.3. Installation du convertisseur de débit ····················2-6
3.3.1. Montage mural (Convertisseur de débit :
FSV...S (IP66) ················································2-6
(Convertisseur de débit : FSV...S (IP66) ········2-6
3.3.3. Montage mural (Convertisseur de débit :
FSV...H (IP67) ················································2-7
(Convertisseur de débit : FSV...H (IP67)········2-7
3.4. Câblage du convertisseur de débit························2-8
3.4.1. Avertissements relatifs au câblage ·················2-8
3.4.2. Câbles électriques utilisables ·························2-8
3.4.3. Traitement des passages de câbles ···············2-8
3.4.4. Câblage des borniers······································2-9
3.4.4.1. Convertisseur de débit : FSV...S (IP66) ··2-9
3.4.4.2. Convertisseur de débit : FSV...H (IP67) 2-10
4. PARAMETRES ························································4-1
convertisseur···················································4-1
4.1.1. Convertisseur de débit : FSV...S (IP66)
unité d'affichage/réglage·································4-1
4.1.2. Convertisseur de débit : FSV...H (IP67)
unité d'affichage/réglage·································4-1
4.2. Composition des menus········································4-3
4.2.1. Menus en anglais············································4-3
4.2.2. Menus en français ··········································4-8
4.3. Liste des paramètres par défaut··························4-13
4.4. Paramètre de protection······································4-15
4.4.1. Paramètre de protection ON/OFF·················4-15
4.5. Langue affichée···················································4-16
Sommaire
4.5.1. Comment sélectionner la langue ··················4-16
4.6. Réglage des paramètres de la canalisation ········4-17
canalisation ···················································4-17
canalisation ···················································4-18
4.7. Réglage du zéro ··················································4-21
4.8. Réglage des unités··············································4-22
4.8.1. Configurer le système d'unités······················4-22
4.8.2. Configurer l'unité de débit ·····························4-23
4.8.3. Configurer l'unité du totalisateur ···················4-24
4.9. Réglage de la sortie ············································4-25
4.9.1. Réglage de l'échelle de débit························4-25
4.9.1.1. Réglage de l'échelle de débit (échelle
4.9.1.3. Limites de sortie ·····································4-27
4.9.2. Réglage du totalisateur ·································4-28
4.9.2.3. Mode totalisateur (RAZ, MARCHE,
4.9.3. Réglage des sorties logiques (DO) ···············4-33
4.9.4. Réglage de l'indicateur LCD ·························4-35
4.9.5. Réglage du temps de réponse······················4-36
4.9.6. Réglage de la chute à zero à bas débit ········4-37
4.10. Paramètres spécifiques à l'application ··············4-38
4.10.2. Réglage échelle bi-directionelle ··················4-40
4.10.3. Réglage 2 échelles bi-directionnelle à
4.10.4. Limite vitesse ··············································4-44
4.10.5. Réglage de la sortie logique (DO)···············4-45
4.10.6. Configuration de l'entrée logique (DI) ·········4-52
4.10.6.1. Desactivation de l'entrée DI ·················4-52
-v-
simple)·····················································4-25
erreur (Défaut)·········································4-26
(valeur d'impulsion, largeur d'impulsion) ·4-28
zéro ·························································4-30
ARRET) ···················································4-31
une erreur (BURNOUT)···························4-32
totalisateur···············································4-33
automatique ···············································4-38
communtation automatique························4-42
d'échelle ? ············································4-45
pour signaler un défaut?·······················4-46
impulsion) ·············································4-50
débit ?···················································4-51
avec un contact externe? ·····················4-53
Publicité
Table des Matières
