Care And Maintenance; In The Event Of A Problem - Rowenta PU2532 Mode D'emploi

CARE AND MAINTENANCE

Before performing any maintenance work, switch off the air purifier using the on/off button (1).
Use a damp cloth to clean the surface of the product.
Important: Do not use any abrasive materials, as these may damage the surface of the product.
Frequency of cleaning/replacing the filter :
Filter
Pre filter
2in1 Active Carbon & Allergy + HEPA filter
Before carrying out any maintenance operation, be sure to unplug the power plug. You can use a slightly wet
cloth to clean the purifier body.
Important: Do not clean it with anything of grinding nature to avoid damaging to the surface of the purifier.
• When the 2-in-1 filter reaches 95% of saturation, the filter indicator will light up and the buzzer will ring
for one minute to remind the user to replace the 2-in-1 filter.
• * The flashing light indicates that the usage of the filter mesh is about to end.
• The filter indicator will flash when the 2-in-1 filter is full of dust then you must replace it with a new 2-in-1
filter
Performing a force reset:
The filter indicator lights up on the control panel and the buzzer rings for one minute each time the purifier
is switched on, to remind the user to replace the 2-in-1 filter. After you replace it, press the On/Off button (1)
for 3 seconds to reset the filter.
If the 2-in-1 filter is replaced before its end of life, the timing of the 2-in-1 filter should be reset by force:
1. After replacing the 2-in-1 filter, press and hold the sleep mode button for 3 seconds;
2. The corresponding filter indicator light flashes;
3. Press and hold the sleep mode button for 3 seconds again, the filter indicator light goes out and the
buzzer beeps twice, then the purifier will recalculate the usage of the 2-in-1 filter.
4. The reset mode will be canceled, if there is no operation for 3 seconds
Caution :
*The working efficiency of the pre-filter will be reduced if not cleaned regularly
*Do not use a wet pre-filter
*Do not wash or reuse the 2-in-1 filter
* Replace the filter mesh in turns, please refer to "Before use" ------"Frequency of cleaning/replacing the filter"
Please note: certain filters may emit a temporary slight odour, due to the transport and storage conditions.
« TIPS FOR CHANGING FILTERS »
• Avoid handling used filters if you suffer from allergies or asthma.
• Wear gloves when changing the filters, or wash your hands well afterwards.
• Put used filters directly into a closed, air-tight bag before throwing them away to avoid
spreading pollutants.
IMPORTANT:
Never use a detergent or metal object to clean the sensors.
The efficiency of the sensors may be reduced if not cleaned regularly.
Cleaning frequency varies depending on the operating environment of the appliance. If it is used in a dusty
environment, clean the sensors more frequently.
STORAGE
When you are not using the appliance, store it in a cool, dry place with ambient conditions no higher than 35°C
70%RH.
6
Clean/replace Frequency
Clean Every 2 months
Replace Every 12 months

IN THE EVENT OF A PROBLEM

• Do not disassemble the appliance yourself. A poorly repaired appliance may be dangerous for the user.
• Check the troubleshooting table below before contacting an Approved Service Center:
Problem
Filter codes
The appliance does not
switch on.
XD6220U0
The flow is a lot weaker
than before.
There is an unpleasant
smell coming from the air
outlet.
WARRANTY
Do not use the appliance and contact an Approved Service Centre if:
– your appliance has been dropped;
– your appliance or its power cord are damaged;
– your appliance no longer functions properly.
You can find a list of Approved Service Centres on the Rowenta international warranty card.
HELP PROTECT THE ENVIRONMENT!
Your appliance contains many materials which can be recovered or recycled.
Leave it at a local waste collection point or take to an approved service center so that it can be
processed.
These instructions can also be found on our internet site, at www.rowenta.com.
Check
Connect the power cord to a plug
Is the power cord connected?
with the correct voltage.
Press the on/off button and select the
Are all the display elements off?
You can use your purifier once the
Is there a power outage?
power turns on again.
Check the filter cleaning and
Does the filter need to be cleaned or
replacement frequencies and clean/
replaced?
replace the filter(s) if necessary.
Check the filter cleaning and
Is the sensor lens covered with dust? replacement frequencies and clean/
replace the filter(s) if necessary.
Solution
EN
required function.
7