SoftBank pepper Guide Rapide page 7

Only use the recommended battery charger provided with
Pepper. Other chargers may damage the Charging Station
and may cause fire or electric shocks.
Do not touch the Charging Station during a storm. The
Charging Station can cause an electric shock.
Do not use the Charging Station in (or with) any heating
appliance, for example ovens, IH cooker, etc. It may cause
overheating, smoke, fire, or malfunction.
Do not use the Charging Station where humidity is saturated
or water may splash such as a bathroom. It can cause fire
or electric shock.
Verify that the available supply voltage is adequate for the
Charging Station.
When using a power extension cable or a multiple socket
adapter, make sure it is grounded and has sufficient current
rating.
If there is dust on the plug, it may cause fire. Unplug the
Charging Station and clean the plug with a soft dry cloth.
Connect the Charger to the wall socket before connecting to
the Charging Station.
If unused for a long period (e.g. a week), unplug, and store in
an area free from dust.
The Charging Station must not be subjected to any impact
or other force, whether plugged or unplugged. This can
cause fire, injury or damage.
Ensure the Charging Station is used in a clean area. Small
objects or particles can get stuck in Pepper's wheels while
docking or undocking and can cause fire, injury, damage or
malfunction.
If there is smoke, sparks or smell coming from the Charging
Station casing, unplug immediately from the wall socket
and contact Pepper technical support.
Do not step on the Charging Station or put objects on it
other than the Robot.
Do not step on the cable of the Charging Station or put
objects on it other than the Robot.
If the cable is damaged, do not use it.
Since there is no ON/OFF switch, ensure there is easy
access to the wall socket.
Do not pull on the power cable to unplug. Remove the plug
from the wall socket
Maintenance
To clean the Charging Station:
1.
Unplug all cables from the Charging Station.
2.
Unplug the Charger from the wall socket.
3.
Clean the dust and dirt on the surface of the Charging
Station using a soft damp cloth.
4.
Wipe off with a dry cloth.
• Do not use abrasives, aerosols or other fluids, as they may
contain flammable substances or may damage the plastic
finish. Never spray or submerge the product in water or any
other liquid.
• Do not disassemble. You don't need to maintenance internal
parts.
• Use the Charging Station only when it is completely dry.
LED notifications
Flashing blue (1 s) Start up
Steady Blue Ready to use
Caution
Attention
Off Charging
Flashing red Error*
*If the LEDs are red, unplug the Charging Station and plug it
again. If the problem persists, please contact Customer Care
(refer to the Pocket Guide).
Specification
Input voltage
Output voltage
Output current
Dimension (hxwxl)
Cable length
Weight
Waterproof level
Compliance information and symbols
The labels are found under the Charging Station.
Europe: Waste Electrical and Electronic
Equipment Directive is the European
Community directive 2012/19/UE
Europe: Complies with CE directives and
regulations
Japan: VCCI certification
Complies with the VCCI rules
China: Complies with GB 60 950
Do not use in tropical climate regions
China: Complies with GB 60 950
Do not use at altitude exceeding 2000m
NRTL Curtis Strauss Mark: Complies with
ANSI/UL rules for the US and Canada
Australia (RCM mark): complies with
Australian regulations and requirements
Indoor use only
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Materials
Item Material / Coating
Casing PP, ABS-PC, Silicone, Paint, UV coating
LED PC
Socket ABS-PC, Silicone, Paint / UV coating
Connectors Beryllium copper
29.2 V DC
29.2 V DC
8.0 A
75 x 390 x 370 mm
(2.95 x 15.35 x 14.56 in)
1.3 m (4.26 ft)
1.86 kg (2.87 US lb)
IPX0
5