Sommaire des Matières pour Flextherm GreenCableCONCRETE
Page 1
INSTALLATION GUIDE For GC series heating cable sets GUIDE D’INSTALLATION Pour ensembles de câbles chauffants série GC SPREAD THE WARMTH LA CHALEUR HUMAINE...
Required Materials and Tools The FLEXTHERM seal on the cable warrants the integrity of the cable. The cable cannot be returned if the seal is broken. As a quality assurance measure, each cable has been subjected to a 1,500 V dielectric test and resistance test.
Page 3
Picture 3 Anchor it to the mesh with FLEXTHERM adhesive tape (picture 4). Ensure that Should the results obtained not comply with cable specifications, do the mechanical joint is attached outside of the cable conduit and in the zone not break the cable seal and contact FLEXTHERM customer service at where concrete will be poured.
The mechanical joint must also be embedded in the concrete. Parquet • The FLEXTHERM adhesive tape is the only recognized Carpet (without rubber backing method of cable installation on a wire mesh. The use of any or carpet padding) other method will automatically void the limited warranty.
Page 5
Installation with two cables Securing the cable to the mesh Install the cable to the mesh in a winding path manner, using the FLEXTHERM adhesive tape. The required amount of adhesive tape is included in your kit. Fasten the cable with the adhesive tape as the work progresses, always respecting the pre-determined spacing.
Page 6
Should the cable have been damaged during installation, * Applications must be validated with local and/or national electrical codes do not proceed with the concrete pouring. Contact FLEXTHERM Customer Floor Probe Installation Service at 1 800 353-9843.
Compatible Thermostats Use FLEXTHERM thermostats to operate the system. These thermostats are equipped with a built-in Class A ground fault circuit interrupter (GFCI) that will protect the system in case of fault. To preserve the system’s warranty, the use of a control equipped with a Class A GFCI (5 mA) is required.
Le sceau du câble est garant de son intégrité. Le câble ne peut être retourné si le sceau est brisé. Afin d’assurer la qualité du produit, chaque câble FLEXTHERM Pour procéder à l’installation de votre système vous aurez besoin des articles est vérifié, en usine, par un test résistif et un test diélectrique à...
Si les résultats des tests ne sont pas conformes, ne pas retirer le sceau autour de la bobine et contacter le service à la clientèle de FLEXTHERM au 1-800-353-9843. Installation électrique préliminaire Circuit Les systèmes de planchers chauffants FLEXTHERM doivent être raccordés...
FLEXTHERM. de la garantie limitée. Si votre choix est porté sur le plancher flottant, certains facteurs pourront influencer la • Pour une installation sur des treillis à losanges ou sur...
Installation avec deux câbles Fixation du câble au treillis Fixer le câble au treillis à l’aide du ruban FLEXTHERM, en faisant des serpentins. La quantité nécessaire de ruban a été incluse dans votre ensemble. Fixer le câble à l’aide du ruban au fur et à mesure de l’avancement de l’installation, et ce, en respectant l’espacement préétabli.
Placer le tuyau de façon à ce que le capillaire à la clientèle de FLEXTHERM au 1 800 353-9843. de la sonde soit à une distance minimum de 60 cm (2 pi) à l’intérieur de la zone chauffée.
Fixer le fil vert (mise à la terre) à la borne dans la boîte électrique. Procéder au raccordement en suivant les directives prévues dans le guide d’installation du thermostat FLEXTHERM. Identifier ensuite le circuit approprié au panneau électrique. Installation multiple Dans le cas d’une installation qui nécessite plus d’un circuit, se procurer un...
Page 14
FLEXTHERM Inc. 2400 de la Province, Longueuil, Québec J4G 1G1 Canada Tel. 1 800 FLEXTHERM (353-9843) • 450-442-9990 Fax. 1 877 FLEXTHERM (353-9843) • 450-442-1099 client@flextherm.com www.flextherm.com...