Hella marine Sea Hawk-XLB Manuel D'instructions

INSTRUCTION SHEET:
Hella marine LED products offer many advantages over conventional bulb lamps. Significantly reduced power consumption, ultra long
life and high tolerance to shock and vibration make HELLA LED lamps the ideal choice for the harsh marine environment.
Housing Material 'Non-metal' thermally conductive housing
Lens Material Heavy duty Grilamid
®
Bracket Material 316 Stainless steel
Light Source LED
Light Output ~2200 lumen (5000K white)
Operating Voltage Multivolt TM 9-33V DC
Power Consumption High 25W ( 2A @ 12V DC / 1A @ 24VDC)
Low 5W (not applicable to pencil beam models)
Cable Pre-wired with 2.5m tinned marine cable
Degree of Protection IP 6K7 IP6K9K (Completely sealed)
Weight 840g (including cable)
Operating Temperature -40°C to +60°C (-104°F to + 140°F)
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress possible interference, both
emission as well as susceptibility, to the limits prescribed in international regulations.
Electrical Protection
This lamp is protected against overvoltage, voltage spikes, reverse polarity connection and negative voltage spikes.
Wiring and High / Low mode activation
High intensity mode is acheived by connecting positive (red) and negative (black or white) to a DC power supply.
Low intensity mode* is acheived by connecting positive (blue or brown) and negative (black or white) to a DC power supply.
Switching between Low and High modes can be achieved using any standard ON / OFF / ON switch. (Hella P/N 4202)
Lamps with Black housing
Cable colour Connect to Consumption
Black or White Negative (-) -
Red Positive (+) 25 watts
*
Positive (+) 5 watts
Brown
*Low mode not available on pencil beam models
LED modules are polarity conscious. Reverse polarity will not damage this product but will inhibit its function. HELLA recommends
wire connections be soldered, and heat shrink tubing applied to seal the joint. Each lamp must be protected by a fuse rated at
5 amperes maximum.
408 mm
408mm (16.06")
Single Bracket
340 mm
340mm (13.38")
404 mm
404mm (15.9")
Optional
Double Bracket
Accessory
340mm (13.38") 340 mm
404 mm
404mm (15.9")
www.hellamarine.com
Sea Hawk-XLB LED Deck Light
Lamps with White housing
Cable colour Connect to Consumption
Black or white Negative (-)
Red Positive (+) 25 watts
*
Positive (+) 5 watts
Blue
Dimensions
67mm (2.64")
67 mm
34 mm 8 mm 34mm 8mm
(1.34") (0.31")
73mm (2.87") 73 mm
30mm
30 mm
(1.18")
8mm
8 mm
40mm
40 mm (0.31")
(1.57")
Designed and Manufactured in New Zealand
Sea Hawk-XLB Deck Floodlights are supplied with brackets that require assembly. Before assembly please check that all
components have been supplied and read all instructions prior to installation.
ATTENTION: Each adaptor will be supplied pre-assembled, you must remove the thumb knob before clipping the adaptors onto
the lamp. Ensure each adaptor is fitted with the supplied stainless steel nut before clipping onto the lamp. The nut cannot be
fitted once the adaptor has been clipped onto the lamp.
CAUTION! Use only the provided M8 x 20mm bolt. Using a longer bolt may damage the lamp and void warranty.
2x 2x
2x
Thumb Knob
(Pre-assembled)
1x 1x 2x 2x 2x
Mounting Adaptor
2 x
2x
2x
2 x
3: Choose a suitable mounting location
1x 1x
-
Congratulations! The product you have selected comes from HELLA – one of the world's leading manufacturers of lighting products.
The product comes with a 5 year warranty from end user purchase covering faults in materials, components or workmanship.
In the unlikely event that you should experience a confirmed warranty related problem with your purchase, HELLA will, at its discretion, either
repair, replace or refund the purchase price of the product. Warranty services may be obtained by returning the product within the warranty
period to the HELLA dealer where the product was originally purchased.
This warranty is in addition to and does not preclude any other rights or remedies available to the consumer under any local legislation related
to the provision of goods or services.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty does not cover:
1. Claim/s as a result of normal wear and tear or of any modifications and / or alterations to the product in any shape or form.
2. Claim/s as a result of non-compliance of the assembly, service and operating instructions and/or any unfit or improper use.
3. Any expenses incurred in the process of making the claim.
Note: For lamps sold in Australia warranty services are provided by: Hella Australia Pty Ltd, 54-76 Southern Rd, Mentone VIC 3194
Customer Service 1800 061 729
Mounting Instructions
M8x20 mm
1: Scope of supply
1
1 x XLB Lamp XLB Lamp
1
2
Ensure each adaptor is fitted with
the supplied stainless steel nut
before clipping onto the lamp.
1x
Stainless Steel Brackets 2x 2x
2x
(Left & Right)
Not included with all models
3
2 x
2x
1 x 1x 1 x 1x 2x 2x
4: Securely fasten lamp onto desired mounting location.
2x 2x 2x
Warranty
www.hella.com/hella-au/21.html
For general comments about Hella marine products please email techfeedback@hellamarine.com
M8x20 mm
2: Clip adaptors onto lamp then assemble bracket.
1
M8x20 mm
2
2
ATTENTION
1
CAUTION!
Use only the provided
M8 x 20mm bolt.
2
Using a longer bolt may damage
the lamp and void warranty.
2x
7mm
Ø7 mm
(0.27")
Ø7 mm 7mm
(0.27")
25 mm
25mm (1")