fadini Junior 633 Notice D'instructions page 21

JUNIOR 633
JUNIOR 650
CE DECLARATION OF CONFORMITY of the manufacturer:
Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that: Junior 633 complies
with the 2006/42/CE Machinery Directive, and also that it is sold to be installed in an "automatic system", along with original
accessories and components as indicated by the manufacturing company.An automatic gate operator is, by law, a "machinery"
and therefore the installer must fit the equipment with all of the applicable safety norms. The installer is also required to issue
the installer's Declaration of Conformity. The manufacturer is not liable for possible incorrect use of the product. The product
complies with the following specific norms: analysis of the risks and subsequent action to cure them as per EN 12445 and EN
12453, Low Voltage Directive 2014/35/UE, Electromagnetic Compatibility 2014/30/UE.
In order to certify the product, the manufacturer declares under own responsibility the compliance with the EN 13241-1
PRODUCT NORMS.
Tested and certified: marking and type testing according to ITT - PDC/0977-2010 - 30/04/2010.
Notified institute and laboratory for product certification according to DM 2004/108/EC:
Istituto di Ricerche e Collaudi M.Masini srl - Via Moscova, 11 - 20017 Rho (MI)
- CE 0068 - Notified
- SINCERT 047A Certified - SINAL 0019 Certified
- Conforming to the following Standards: UNI EN 13241-1, UNI EN 12604, UNI EN 12605, UNI EN 12445, UNI EN 12453
CE DECLARATION OF CONFORMITY of the manufacturer:
Meccanica Fadini snc (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that: Junior 650 complies
with the 2006/42/CE Machinery Directive, and also that it is sold to be installed in an "automatic system", along with original
accessories and components as indicated by the manufacturing company.An automatic gate operator is, by law, a "machinery"
and therefore the installer must fit the equipment with all of the applicable safety norms. The installer is also required to issue
the installer's Declaration of Conformity. The manufacturer is not liable for possible incorrect use of the product. The product
complies with the following specific norms: analysis of the risks and subsequent action to cure them as per EN 12445 and EN
12453, Low Voltage Directive 2014/35/UE, Electromagnetic Compatibility 2014/30/UE.
In order to certify the product, the manufacturer declares under own responsibility the compliance with the EN 13241-1
PRODUCT NORMS.
Tested and certified: marking and type testing according to ITT - PDC/0978-2010 - 30/04/2010.
Notified institute and laboratory for product certification according to DM 2004/108/EC:
Istituto di Ricerche e Collaudi M.Masini srl - Via Moscova, 11 - 20017 Rho (MI)
- CE 0068 - Notified
- SINCERT 047A Certified - SINAL 0019 Certified
- Conforming to the following Standards: UNI EN 13241-1, UNI EN 12604, UNI EN 12605, UNI EN 12445, UNI EN 12453
MAIN COMPONENTS FOR INSTALLATION
1
1 m
1 - Junior series sliding electro-mechanical Junior 633/
Junior 650 operator complete with programmer Elpro 63
2 - N° 2 coded keys for manual unlocking
3 - Base plate
4 - N° 4 Anchor bolts
5 - N° 8x M10 hexagonal nuts+washers
6 - LH magnet bracket for limit switch
electro-mechanical sliding gate operator
2 3
8
1 m
4 5
9 10
7 - RH magnet bracket for limit switch
8 - Nylon gear rack (not supplied in the kit)
9 - 30x8 steel gear rack (not supplied in the kit)
10 - N° 30 pcs. Self-threading screws with square washer for
nylon gear rack (not supplied in the kit)
11 - N° 30 pcs. Washers and fixing bolts for steel gear rack
(not supplied in the kit)
21
Meccanica Fadini s.n.c.
Director in charge
Meccanica Fadini s.n.c.
Director in charge
6 7
11