Pentair SHURFLO Guide Rapide

SHURFLO
CITY/CURBSIDE POTABLE WATER ENTRY
®
INSTALLATION INSTRUCTIONS
The SHURFLO Water Entry is a pressure reducing device which maintains nominal pressure and prevents high pressure surges
from damaging the plumbing system. All Water Entries contain an internal backflow preventer to stop reverse flow through the
unit when the potable water pump is used.
CAUTION: Maximum inlet pressure is 125 psi. [8.6 bar]
FLEXIBLE
TUBING
WALL/BULKHEAD MOUNTING
❚ Choose a location that permits easy
access to the outlet (pressurized)
plumbing. The preferred plumbing con-
figuration is to tee into the cold water
line after the pump but, before the water
heater or fixtures.
❚ Cut a 3½" dia. [8.75 cm] opening.
❚ Place the unit into the opening, and
square the mounting holes. Mark the
four mounting holes.
❚ Use #8 screws/hardware (not includ-
ed) that are applicable for wall construc-
TUYAUTERIE
tion and environment.
FLEXIBLE
❚ Drill the four mounting holes required
for the fasteners.
❚ Make consideration for plumbing
connections that may be easier to make
prior to the unit being mounted.
183- 2
# X
50 PSI
[3.4 BAR]
70
[4.8]
60
[4.0]
O
50
U
[3.4]
T
40
P
[2.8]
U
30
[2.1]
T
20
[1.4]
30 40 50 60
[2.1] [2.8] [3.4] [4.0]
INPUT
FLOW MANAGEMENT SOLUTIONS
WATER TANK
❚ Use at least 1 ft. [30 cm] of ½" I.D.
[13mm] flexible high pressure tubing if
connecting to rigid plumbing.
CAUTION: The Water Entry must not
be connected directly to plastic or rigid
pipe. Vibration or stress induced through
the plumbing may cause noise and pos-
RÉSERVOIR D'EAU
sibly loosen or crack components.
❚ The swivel-barb fitting (available p#
244-3926 elbow, 244-2926 straight) is
designed with a "taper seal" creating
a water tight connection when "Hand-
Tightened." Max. torque 8-10 ft/lb. [10-
13 N•m]. Always secure tubing connec-
tions with properly sized stainless steel
clamps.
❚ Seal flange with suitable caulking to
prevent exterior water from damaging
wall construction.
-0
X X
NOMINAL
70
[4.8]
60
[4.0]
O
50
U
[3.4]
T
40
P
[2.8]
STATIC
U
1 GPM
[3.78 LPM] 30
[2.1]
2 GPM T
[7.5 LPM]
20
[1.4]
70 80 90 100 30
[4.8] [5.4] [6.1] [6.8] [2.1]
911-312 REV. T
PUMP
POMPE
183- 2 -1
# X X X
65 PSI
NOMINAL
[4.4 BAR]
STATIC
1 GPM
[3.78 LPM]
2 GPM
[7.5 LPM]
40 50 60 70 80
[2.8] [3.4] [4.0] [4.8] [5.4]
INPUT
HOT
TO FIXTURES
COLD
HEATER
IN-LINE WATER ENTRY
CAUTION: Maximum inlet pressure 125
psi. [8.6 bar].
❚ Install the plastic garden hose adapter
(available p# 244-2356) to the ½–14
thread of the Water Entry.
CHAUD
❚ Use thread sealers sparingly as they
act as a lubricant and may permit over
AUX MONTAGES
torquing.
FROID
RÉCHAUFFEUR
Hand-Tighten Only!
Max. torque 8-10 ft/lb. [10-13 N•m].
CAUTION: Over-torquing or bottoming
threads may damage the unit which is
not covered under warranty.
❚ Water Entry may be capped and left at-
tached to the potable water hose during
storage.
90 100
[6.1] [6.8]
1