Sport-thieme G811ST Instructions De Montage Et Utilisation page 12

3 Parents and/or those responsible for children should
always take their curious nature into account and how this
can often lead to hazardous situations and behaviour
resulting in accidents. This unit does not have to be used
in any case like toy.
4 The owner is responsible for ensuring that anyone who
uses the machine is duly informed about the necessary
precautions.
5 Your unit can only be used by one person at a time.
6 Use suitable clothing and footwear. tie up your shoelace
correctly.
ASSEMBLY INSTRUCTIONS.-
ATTENTION: The assistance of a second person is
recommended when assembling this machine.
It is advisable to retighten these screws after one
month of using the machine.
1. Take the unit out of its box and make sure that all of the
pieces are there:
Fig.1 Parts list
(1) Main body.
(155) Bottom post cover.
(97) Main post.
(49) Front stabiliser bar with wheels.
(59) Rear stabiliser bar with adjustable feet.
(108) Bottom focus bar, left.
(107) Bottom focus bar, right.
(129) Pedal left foot.
(130) Pedal right foot.
(110) Left focus bar or arm.
(111) Right focus bar or arm.
(I) Monitor.
(220) Bottle holder.
(154) Left footrest.
(154) Right footrest.
(221) Transformer.
(63) Bottom cover.
Fig.2 Screws and fasteners
(123) Washers 29x26x0,35.
(157) Screws M-4x15.
(101) Washers M-10.
(100) Self locking nuts M-10.
(122) Self locking nuts M-8.
(132) Self locking nuts M-12.
(139) Screws M-12x40.
(119) Screws M-8x15.
(121) Screws M-8x45.
(156) Screws M-5x15.
(158) Screws M-5x10.
(120) Washers 30x9x2.
(89) Screws M-8x15.
(201) Washers 22x9x2.
(66) Spring washer M-10.
(90) Washers 25x9x2.
(200) Screws M-8x15.
(91) Curved washer BK.
(98) Screws M-10x70.
(99) Screws M-8x15.
(67) Washers M-10.
(159) Washers M-6.
(68) Screws M-4x15.
(89) Screws M-8x15.
(51) Cap nut M-8.
(65) Screws M-10x40.
(160) Screws M-5x10.
(161) Screws M-6x15.
(162) Washers M-6.
Allen key 8mm.
Allen key 10mm.
Allen key 6mm.
Allen key 5mm.
Ended ring spanner 19mm.
Double ended ring spanner 10-13.
2. FITTING THE STABILISER BARS.-
Bring the front stabiliser bar with wheels (49) to the main
body (1) positioning the wheels at the front of the unit,
Fig.3, and self locking nuts (51), and tighten securely.
Carry out the same operation to attach the rear stabiliser
bar.
Take the rear stabiliser with adjustable feet (59), and line
up the dots, Fig.4. Insert the screws (65), fit the washers
(67) and spring washer (66), and tighten securely.
Next, fit the rear trim cover (63) (145) and tighten using
screws (68) (160), Fig.5.
3. FITTING THE FOOT BARS.-
Fit the spacer washers (91) as shown in Fig.6.
Then fit take the left foot (129) (marked with the letter "L")
and insert the end bush onto the drive spindle (E) on the
main body (1) Fig.6.
Insert screw (89), as shown in Fig.6, then fit the flat
washer (90) and tighten securely.
Take the right foot bar (130), (marked with the letter "R")
and go through the same assembly procedure as with the
left Fig.7.
4. FITTING THE BOTTOM POST COVER.-
Take the main post (97) Fig.8 and insert the bottom post
cover (155) in the direction of the arrow, Fig.8.
5. FITTING THE MAIN POST.-
Next, bring the main post (97) up to boss on the main
body (1), Fig.9, connect the terminals (208) and (209),
Fig.9.
Slip the main post (97) over the boss on the main body
(1) in the direction of the arrow, Fig.9, making sure not to
snag any of the cables.
Refit the screws (98)(99), the washers (100)(101) Fig.9,
and tighten securely.
6. FITTING THE MONITOR.-
Next, connect terminals (208), sticking out of the
handlebar (97), and terminal (B), sticking out of the
monitor (I), Fig.10.
12
G811ST