For Your Safety - Würth master PM 200-E Notice Originale

PM 200 E.book Seite 11 Mittwoch, 29. April 2009 1:32 13
GB
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
Working safely with this machine is
possible only when the operating and
safety information are read completely
and the instructions contained therein
are strictly followed. In addition, the
general safety instructions in the
enclosed booklet must be followed.
Please also observe the relevant national industrial
safety regulations.
Wear safety goggles.
Wear protective goggles, ear protec-
tion.
Wear protective gloves.
Safety warnings common for sanding,
sanding with sanding sheets, working with
wire brushes, polishing and cut-off
grinding
This power tool is intended to function as a sander,
wire brush or polisher. Read all safety warnings,
instructions, illustrations and specifications pro-
vided with this power tool. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury.
Operations such as grinding or cutting-off are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufac-
turer. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can fly apart.
All manuals and user guides at all-guides.com

For Your Safety

The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the spindle
of the power tool. Accessories with arbour holes that
do not match the mounting hardware of the power
tool will run out of balance, vibrate excessively and
may cause loss of control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pads for cracks, tear or
excess wear, wire brushes for loose or cracked
wires. If the power tool or accessory is dropped,
inspect for damage or install an undamaged acces-
sory. After inspecting and installing an accessory,
position yourself and bystanders away from the
plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart dur-
ing this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and shop apron capable
of stopping small abrasive or workpiece frag-
ments. The eye protection must be capable of stop-
ping flying debris generated by various operations.
The dust mask or respirator must be capable of fil-
trating particles generated by your operation. Pro-
longed exposure to high intensity noise may cause
hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of the
workpiece or of a broken accessory may fly away
and cause injury beyond the immediate area of
operation.
Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own
power cord. Contact with a "live" wire will also
make exposed metal parts of the power tool "live"
and shock the operator.
Position the cord clear of the spinning accessory. If
you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spin-
ning accessory.
Never lay the power tool down until the accessory
has come to a complete stop. The spinning acces-
sory may grab the surface and pull the power tool
out of your control.
Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
11