Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Start-up and use
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring
showing the strength of the flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an
anticlockwise direction so that it is pointing to the
maximum flame setting .
3. Adjust the intensity of the flame to the desired level
by turning the BURNER knob in an anticlockwise
direction. This may be the minimum setting , the
maximum setting or any position in between the two.
If the appliance is fitted with an electronic lighting
device* ( C ), press the
BURNER knob and turn it in
X
an anticlockwise direction,
towards the minimum flame
setting, until the burner is lit.
The burner may be
extinguished when the knob
C
is released. If this occurs,
repeat the operation, holding the knob down for a
longer period of time.
! If the flame is accidentally extinguished, switch off
the burner and wait for at least 1 minute before
attempting to relight it.
If the appliance is equipped with a flame failure
safety device*(X), press and hold the BURNER knob
for approximately 2-3 seconds to keep the flame
alight and to activate the device.
To switch the burner off, turn the knob until it
reaches the stop position •.
Practical advice on using the burners
For the burners to work in the most efficient way
possible and to save on the amount of gas
consumed, it is recommended that only pans that
have a lid and a flat base are used. They should
also be suited to the size of the burner:
Burner
ř Cookware diameter (cm)
Fast (R)
Semi Fast (S)
Auxiliary (A)
To identify the type of burner, please refer to the
diagrams contained in the "Burner and nozzle
specifications".
*
Only available in certain models.
All manuals and user guides at all-guides.com
! For models equipped with a reducer grid, the latter
must be used only for the auxiliary burner, when
pans with a diameter of less than 12 cm are used.
Electric hotplates*
The corresponding knob may be turned clockwise or
anti-clockwise and set to six different positions:
Setting Normal or Fast Plate
When the selector knob is in any position other than
the off position, the 'on' light comes on.
Using the oven
! The first time you use your appliance, heat the empty
oven with its door closed at its maximum temperature
for at least half an hour. Ensure that the room is well
ventilated before switching the oven off and opening
the oven door. The appliance may emit a slightly
unpleasant odour caused by protective substances
used during the manufacturing process burning away.
! Never put objects directly on the bottom of the oven;
this will avoid the enamel coating being damaged.
! Before operating the product, remove all plastic film
from the sides of the appliance.
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. Select the recommended temperature for the
cooking mode or the desired temperature by turning
the THERMOSTAT knob.
A list detailing cooking modes and suggested
cooking temperatures can be found in the relevant
table ( see Oven cooking advice table ).
During cooking it is always possible to:
• Change the cooking mode by turning the
• Change the temperature by turning the
24 - 26
16 - 20
• Stop cooking by turning the SELECTOR knob to
10 - 14
! Always place cookware on the rack(s) provided.
! Should the appliance be equipped with an
electronic programmer, to use the electric oven, just
press buttons
symbol will appear on the display) before selecting
the desired cooking function.
0
Off
1
Low
2 - 5
Medium
6
High
SELECTOR knob.
THERMOSTAT knob.
the "0" position.
and
at the same time (the
GB
11
Publicité
Table des Matières
