Télécharger Imprimer la page

Publicité

Liens rapides

Models/Modelos/Modèles
6310
Series/Serias/Seria
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:
For easy installation of your Brizo
faucet you will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and maintenance
information.
• To purchase the correct water supply hook-up.
Para instalación fácil de su llave
Brizo
usted necesitará:
®
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
• Comprar las conexiones correctas para el
suministro de agua.
Pour installer votre robinet Brizo
facilement, vous devez:
• LIRE TOUTES les instructions avant de débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
• Acheter le bon nécessaire de raccordement.
www.brizo.com
THREE HANDLE ROSETTE BIDET VALVE WITH
60903
VACUUM BREAKER AND POP-UP ASSEMBLY
VÁLVULA DE TRES MANIJAS PARA EL BIDÉ DE
BOQUILLA ROCIADORA CON ROMPEDOR DE
VACÍO Y ENSAMBLE DEL DESAGÜE AUTOMÁTICO
ROBINET À TROIS POIGNÉES POUR BIDET AVEC
AJUTAGE, CASSE-VIDE ET RENVOI MÉCANIQUE
®
®
1
T E FLO N
N
O
T
L
E
F
3/32" (2.38mm)
3/32 po (2.38mm)
3/32" (2.38mm)
3/32 po (2.38mm)
9/22/15
Rev. F

Publicité

loading

Sommaire des Matières pour Brizo 6310 Serie

  • Page 1 Inscrivez le numéro de modèle ici. You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin: T E FLO N 3/32" (2.38mm) 3/32 po (2.38mm) For easy installation of your Brizo ® faucet you will need: • To READ ALL the instructions completely before beginning.
  • Page 2 350 South Edgeware Road Componentes electrónicos y pilas (si aplicable) Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1 Todas las piezas (salvo las pilas), si hay, de esta llave de agua Brizo ® están garantizadas al con- 1-877-345-BRIZO (2749) 1-877-345-BRIZO (2749) customerservice@deltafaucet.com customerservice@mascocanada.com...
  • Page 3 RP48447▲ Diverter Handle & Set Screw Manija Desviadora y Tornillo de Ajuste Manette d’inverseur et vis de calage RP23634 RP48448▲ Screw Diverter Body Tornillo Cuerpo Desviador Corps d’inverseur RP24425▲ Handle Shroud Cubierta de la manija Coiffe de la poignée RP24▲ Rod Guide Assembly (Complete) RP23618 Ensamble de la Barra de Guía...
  • Page 4: Cleaning And Care

    HK31 HK32 ▲ ▲ HK33 HK36 ▲ ▲ HK37 ▲ MAINTENANCE Bidet leaks from Rosette Spray: Contact your distributor for handle and accent options/finishes. SHUT OFF WATER SUPPLIES. Replace Seats & Springs (1).* If leak persists: Comuníquese con su distribuidor para obtener opciones en SHUT OFF WATER SUPPLIES.
  • Page 5 INSTALLATION OF DIVERTER VALVE/VACUUM BREAKER Note: Please refer to bidet bowl installation instructions to identify hole location for diverter valve. Hole size must be 1-1/8” diameter minimum. INSTALLATION OF ROSETTE SPRAY Assemble diverter valve (1) with “Y” and gasket (2) as shown in illustration. Slide one rubber cone Insert rosette (1) and rubber washer (2) into washer (3), with smaller tapered end pointing up, onto diverter valve all the way to the base.
  • Page 6 1/2" (12.7 mm) INSTALLATION OF VALVE ASSEMBLIES Remove base (1) and gasket (2) from cold end valve assembly (3). MAKE CONNECTIONS TO WATER LINES: Choose hook-ups for 1/2" I.P.S. connections: Place assembly (1) through proper mounting hole from bottom. Reinstall gasket (1) Ball nose riser (3/8"...
  • Page 7 Step 3b METAL POP-UP Step 3c Remove stopper (1) and flange (2). Apply silicone to underside of flange (1). Insert Remove pivot nut (1). Install horizontal rod (2) and stopper (3) as removable (4) or non- body (2) into sink. Screw flange (1) into body (2). removable (5).
  • Page 8 FLUSH YOUR SYSTEM Turn diverter handle (1) counterclockwise to ‘rim feed’ position. Turn on water supplies (2) and turn hot and cold handles (3) to open position for one minute to flush any debris from system. INSTALL HANDLES: Check all connections at arrows for leaks. Re-tighten if necessary, but do not overtighten. Place handle insert (1) onto valve stem (2).