Cleaning And Maintenance; Daily Maintenance - Bionaire BWM001X Manuel D'utilisation

PRE-OPERATING INSTRUCTIONS
1. Disconnect your humidifier from the electrical outlet.
2. Select a location for your humidifier, on a flat surface,
about 10cm away from the wall. Do not place your
humidifier on furniture. A floor location that will not be
damaged by moisture is best.
3. Remove the water tank
A
4. Make sure the base
E
removing the main unit
K
lock ( Fig 2) clockwise to the
D
main unit can be lifted away from the base. To refit the
main unit, position it onto the base then rotate the base
lock counterclockwise to the
FILLING THE WATER TANK
1. Disconnect your humidifier from the electrical outlet.
Remove the water tank.
2. Unscrew the tank cap
B
cold, fresh water (Fig 3). Do not fill with warm or
hot water as this may damage the tank and cause
leaking.
3. Replace the tank cap firmly and then replace the water
tank on the base. The tank will immediately begin to
empty into the base.
4. Plug the power cord into a convenient electrical outlet.
OPERATING INSTRUCTIONS
1. To switch your humidifier on, press the on/off button
. Your humidifier will switch on and the number
F
2 status light will illuminate showing that your
H
humidifier is operating on setting 2 (high).
2. Use the high/low button
(high). The high (2) setting will produce the maximum
moisture and the low (1) setting will produce the
longest run time and quieter performance. It is normal
for the humidifier to take 1 minute or so to boil the
water and produce a mist.
3. To switch your humidifier off, press the on/off button
.
F
4. The medication cup
J
moisture outlet . To use, pour designated humidifier
I
medication into the cup and then turn on your
humidifier as directed. DO NOT add medication to the
water tank. DO NOT add medication to the medication
cup when the unit is already operating.
IMPORTANT:
If you do not plan to use your humidifier for two or more
days, make sure any residual water is drained from the
water tank and base to prevent algae or bacteria growth.
RESET PROCEDURE
When the water tank is empty and the water in the heating
chamber is almost empty, the automatic shut off will
activate. Both status lights
H
operate again until you refill the water tank and reset the
humidifier as outlined below:
All manuals and user guides at all-guides.com
.
is free of foreign objects by
. To remove, turn the base
position until the
position.
and fill the water tank with
to select 1 (low) or 2
G
is located near to the
will flash and the unit will not
1. Switch off then disconnect your humidifier from the
electrical outlet.
2. Remove and refill the water tank. Follow the Daily
Maintenance and Filling the Water Tank instructions
to clean and refill the water tank. Refit the tank onto
the unit.
3. Allow 15 minutes for the automatic shut off to reset.
4. After 15 minutes, plug in the unit and switch on your
humidifier. Within about 1 minute, the unit will begin
to produce moisture. If it does not start working, it is
still too hot. Unplug the unit and wait 15-30 additional
minutes, plug the unit back in. The unit should now be
cool enough and operate normally.

CLEANING AND MAINTENANCE

The following maintenance procedures must be routinely
followed in order to ensure proper, efficient operation of your
humidifier. The unit WILL FAIL if it is not cleaned properly.
Regular cleaning prevents a build up of scale on the heating
element and base. It also prevents microorganisms from
growing on the base and tank. This ensures that maximum
efficiency will be achieved.
We cannot over-emphasize how essential proper cleaning is
to the maintenance and continued use of your unit and the
avoidance of algae or bacteria build-up.

DAILY MAINTENANCE

Allow to cool for 1 hour before maintenance.
1. Switch off then disconnect your humidifier from the
electrical outlet.
2. Remove the water tank then unlock the main unit. To
remove, turn the base lock (
position until the main unit can be lifted away from
the base.
3. Empty any water and minerals from the base and wash
in warm soapy water. Rinse then dry thoroughly before
use.
NOTE: It is imperative that the base is cleaned
properly. The base is also dishwasher safe (top
rack ONLY) for easy cleaning. Allow the base to dry
thoroughly before using.
4. Wipe the heating element
clean with a soft cloth. The element has a coating
that is designed to be easy to clean and prolong
the operating efficiency of your humidifier. DO NOT
immerse the main unit in water or any other liquid.
DO NOT use any metal or hard objects to clean the
element. Never use detergents, gasoline, kerosene,
glass cleaner, furniture polish, paint thinner or other
household solvents to clean any part of your humidifier.
5. Replace main unit onto the base and engage the base
lock. Refill then refit the water tank.
5
Fig 2) clockwise to the
D
and the main unit
C K