Service And Maintenance Instructions; Troubleshooting; Technical Data; Putting Out Of Operation/Waste Disposal - Textron Klauke EK 120UNV-L Mode D'emploi

Instruction Manual Universal tool
EK 120UNV-L
4.4 Service and maintenance instruction
For every day service the tool has to be cleaned and dried
after each use. The battery cartridge and the charging unit
have to be protected against humidity and dust.
The electric-hydraulic unit is equipped with a controller
enabling the user to see when the next service is due by
fl ashing for 20 sec. at the end of a working cycle.
The unit must be sent to an authorized service center
(ASC) after reaching 10.000 cycles or at the latest after
one year. During this service worn out parts will be ex-
changed, safety relevant components checked and pos-
sibly replaced pre cautiously. This provision serves your
safety and avoids failures through fatigue.
Attention
Maintain power tools thoroughly. Check for
functionality or jamming of moving parts,
breakage of parts and any other condition that
may affect the power tools operation.
Attention
Do not damage the seals of the tool. If the seal
is damaged the warranty claim is void.
Attention
Have damaged parts repaired by a qualifi ed ex-
pert or by a Klauke ASC before use.

5. Troubleshooting

a.) Constant fl ashing/indicating of the light diode display
(pic 1.3).
 see table 1. If the failure can not be solved return the
tool to the nearest service center (ASC).
b.) The tool loses oil.
 R eturn the unit to the manufacturer. Do not open it and
damage the seal of the tool.
HE.13471_D © 09/2010
All manuals and user guides at all-guides.com

6. Technical Data

Weight approx. 6,3 kg
(incl. battery):
Stroke: 42 mm
Crimping force: approx. 108 kN
Battery voltage: 18 V
Battery capacity 3 Ah (RAL2/BL1830)
Charging time: 22 min. (RAL2/BL1830)
Crimping time: approx. 5 s to 8 s
(depending on the connector size)
Crimps approx. 125 crimps
per battery: (Cu 150 mm² DIN 46235)
Max. cutting 40 mm Ø
diameter:
Cutting time: 8 s to 20 s
(depending on the cable size)
Cuts per battery: approx. 75 cuts (4x70 mm² NYY)
Punching time: 5 s with 22,5 mm Ø, 3 mm St37
12 s with 60 mm Ø, 3 mm St37
Capacity: • 60 cycles per battery
with 60 mm Ø in 3 mm mild steel
• 170 cycles per battery
with 22,5 mm Ø in 3 mm mild steel
Hydraulic oil: Rivolta S.B.H. 11
Environmental -12°C to +40°C
temperature:
Sound level: < 70 dB (A) in 1m distance
Vibrations: < 2,5 m/s²
Dimensions: See Picture 2
Attention
Additional instruction manuals are available
free of charge. The part # is HE.13471.
7. Putting out of operation/waste dis-
posal
This unit is subjected to the scope of the European WEEE
(2002/96/EG) and RoHS (2002/95/EEC) directives.
Information about this can be found on our home page
www.Klauke.com under 'WEEE & RoHS'.
Battery cartridges must be specially disposed of accor-
ding to the EEC Battery Guideline.
Attention
Do not dispose of the unit in your residential
waste. Klauke has no legal obligation to take
care of their WEEE outside Germany unless the
product has been shipped and invoiced from
inside your country by Klauke. Please contact
your distributer to fi nd out more how to get your
tool recycled environmentally friendly.
4
GB