Table des Matières
Publicité
INTRODUCTION
This manual is designed to be used by installers. It describes
the systems and methods to be adopted for a correct installation
of the product.
The product is not dangerous for the end user if installed, used
and maintained in accordance with the instructions provided
by the manufacturer and on condition that the electrical and
mechanical parts are kept in perfect working order.
For this reason the instructions provided in this manual must be
meticulously followed.
The supporting structure is highly resistant.
The product is built to conform to standard low -voltage
directives 2006/95/EEC.
The protection class is IPX5 and the rated voltage is 230V; max
3500 W for the steam bath version.
Compliance with the level of safety laid down by European
electromagnetic compatibility directives 2004/108/EEC is
guaranteed by implementing the following European standards
on the product:
EN 55014-1
EN 55014-2
SYMBOLS USED
IN THIS MANUAL
symbols described below are used in this installation manual
and on certain parts of the product itself.
CONVENTIONAL SYMBOLS AND THEIR MEANING.
WARNING
DANGER OF ELECTROCUTION.
Warn user that, if the described operation is not performed
observing safety regulations, there is a risk of electric shock.
WARNING:
GENERAL DANGER.
Warn user that, if the described operation is not performed
observing safety regulations, there is a risk of physical injury.
WARNING:
HOT SURFACE.
Do not touch the steam dispenser during the steam bath! Hot
surface, drops of water can form.
NOTE.
Inform the personnel involved - information that, if not observed,
may lead to minor injuries to people or damage to the product.
WARNINGS.
Inform the personnel involved -important information.
HYDRAULIC INSTALLER.
A skilled technician capable to install the product under normal
conditions and carry out all adjustments, maintenance and
repair jobs on mechanical parts as necessary. The technician is
not authorised to work on live electrical systems.
ELECTRICAL INSTALLER.
A Specialist technician capable of installing the product under
normal conditions, is responsible for all electrical work, such as
ENGLISH
setting, maintenance and repairs. The technician is capable of
working in energized control cabinets or on electrical sockets.
WARNING
Inform features present only in some versions of the products.
OPTIONAL
Items present only if ordered.
CONSUMPTION MATERIAL
Items not provided by the manufacturer.
PICTURES OF THIS MANUAL REFER TO THE RIGHT
VERSION.
ACT IN THE SAME WAY FOR THE LEFT VERSION.
• Before installing the product, check that the fl oor where it
will be installed is suffi ciently levelled, that it can support its
weight (see installation preparations) and that all necessary
inlets and outlets have been provided.
You must also make sure that the walls and/or fl oor, on which
the product will be placed up against/installed, are fully tiled
for the entire extension of the product.
• Product maintenance and setup must be performed exclusively
by specialised service personnel only.
• Remember that all inspection and protective panels must be
refi tted after maintenance or adjustment.
• Due to its weight and size, the appliance must be assembled
installed by more than one person.
• Do not tamper,disable or disconnect the product devices.
• In any case, do not create by-passes or use them for purposes
other than those for which they were installed.
• Do not remove or tamper with the inspection panels and do
not remove or conceal the product identifi cation labels.
• Installation of electrical devices (sockets, switches, lamps,
etc.) inside the bathroom where the appliance is to be installed
must be in compliance with current regulations.
• It is absolutely forbidden to use any type of electrical appliance
inside or next to the product during use.
• The product connection point to the electrical system must
be protected against any contact with the steam generator,
which can reach high temperatures, close to 100° C.
WARNING.
Do not use acetic silicone.
• Read the instructions supplied with the bottle to make sure
that the silicone is not acetic.
• If acetic silicone is used, acrylic parts might be damaged.
• If you need to replace any parts, contact your nearest service
centre and use original spare parts only.
• At the end of the product's life, do not abandon it in the
environment; contact a disposal fi rm.
WARNING.
The manufacturer declines all responsibility:
• If the installation and maintenance instructions contained
herein are not complied with.
• If the product is not used or installed in compliance with the
existing standards of the installed country.
• If the special maintenance is not carried out by qualifi ed
personnel.
14
SAFETY REGULATIONS
Publicité
Table des Matières
