Lutron DIVA DVTV Directives D'installation

Installation Instructions
Please Leave for Occupant
Package Contents and Parts Identification (Figure A)
Side View Front View
Maximum
Light Level
(High End)
Minimum
Light
Level
(low-end)
Operation
The 0-10 volt low-voltage lighting control provides dimming control for
0-10 volt compatible LED drivers, fluorescent ballast and HID ballast.
Minimum light level (low-end) shall be adjusted to optimize
performance.
Important Notes
Please Read Before Installation
Wallbox Dimensions: A single-gang wallbox 3 in high x 2 in wide x
2 ⁄ in deep (76 mm high x 51 mm wide x 63.5 mm deep) will service
1
2
all individual controls.
Wiring Note: Always turn off AC power before installation. Install in
accordance with all local and national electrical codes.
Fluorescent Lamps: For the best dimming performance, new fluorescent
lamps may need to be operated at full light output for a specified amount
of time prior to dimming. Contact the lamp manufacturer for their specific
recommendations concerning lamp seasoning.
Load Rating: A single low-voltage control can control up to 30 mA
of current. Contact Ballast or Driver manufacturer for current source on
control wires to determine maximum load.
Do not connect this control to line voltage.
To be connected to a Class 2 power source only.
Compatible Devices:
Works with all ballasts and drivers that provide a current source
compliant to IEC 60929 Annex E.2.
Compatible Drivers / Ballasts Include the Following:
Advance Mark VII 0-10 V Electronic Dimming Ballasts
Advance XitaniumR LED Drivers
Cree LED LightingR LR24
ELB Electronics 0-10V T8 Ballasts
Metrolight Smart Electronic Ballasts for HID
Osram Sylvania OPTOTRONICR OT DIM Dimming Ballasts
Osram Sylvania QUICKTRONICR POWERSENSER
Osram Sylvania QUICKTRONICR HELIOST T5HO Dimming Ballasts
Universal Lighting Technologies SuperDimR Ballasts
Lutron Eco-10 10 volt option
For a current list of ballast models refer to the Lutron Ballasts Selection Guide.
Driver / Ballast Functionality Check: With power OFF, check
new driver/ballast for functionality prior to installation of control by
connecting the device's purple and pink * wires together. Turn power
ON. The lights should now be at minimum brightness. With power
OFF, disconnect the wires. Turn power ON. The lights should now be at
maximum brightness.
P/N 0301972a
• Low-Voltage Control
• Mounting Screws (2)
• Wire Conectors (5)
• Installation Instructions
* This wire/terminal may be gray in retrofit applications.
DVTV, DVSCTV
0-10 V Preset Dimmer
For use with: 0-10 Volt Lighting Control Devices
Multigang Installations
When installing more than one control in the same wallbox, it may be
necessary to remove all inner side sections prior to wiring (see diagram).
Using pliers, bend side section up and down until it breaks off. Repeat for
each side section to be removed. A physical barrier (partition) must exist
when ganging with line-voltage products.
Installation
1.
TURN POWER OFF to disable the 0-10 volt devices to be dimmed.
2.
Strip wallbox wires to the following lengths:
5/8 in (16 mm) for 16 to 20 AWG (1.0 to 0.50 mm
1/2 in (13 mm) for 10 to 14 AWG (6 to 1.5 mm
Use a wire connector to join one 14 to 18 AWG (1.5 to 0.75 mm
supply wire with one or two 20 AWG (0.50 mm
3.
Wire controls according to the appropriate wiring diagram shown in
the "Wiring" section of this sheet and on the ballast.
4.
Carefully push wires into wallbox allowing room for the control
back cover.
5.
Mount control into wallbox using screws provided. Units must be
mounted vertically (See Figure A).
6.
Turn power ON. Pushing slider up should increase light intensity.
Pushing slider down should decrease light output to approximately
10% of the maximum light level for 10% dimming ballasts.
7.
The minimum light level (low-end) may be adjusted as follows:
a.
Push slider to the bottom-most position (minimum light
intensity) and run lamps for 15 minutes to warm lamps.
b.
Locate minimum light level trimpot adjustment thumb wheel
on the front of the unit (See Figure A).
c.
Turn the thumb wheel counterclockwise to decrease light
level and clockwise to increase light level.
8.
Attach Faceplate.
Troubleshooting
LIGHTS DO NOT OPERATE AT FULL BRIGHTNESS:
• Check to see that purple and pink * wires are not cross connected
in any fixture, conduit, or wallbox.
• Push slider up. Turn high-end trimpot counter-clockwise with a
screwdriver to achieve maximum light intensity. The trimpot is
initially set at the factory to the full counterclockwise position for
maximum light intensity.
LIGHTS DO NOT DIM LOW ENOUGH:
• If the rated dimming range is not achieved, check to see that purple
and pink * wires are not cross connected in any fixtures.
• Push slider down. Turn the low-end trimpot thumb-wheel counter-
clockwise to achieve minimum light intensity.
LIGHTS TURN OFF OR FLICKER AT LOW END:
• Push slider down. Turn the low-end trimpot thumb wheel clockwise
until the lights remain on without flickering.
Dimming Control 10 V- 30 mA
Switch 24 V- 100 mA
) wire.
2
) wire.
2
)
2
) control wire(s).
2
1