Lutron D-603PG Manuel D'instructions

Incandescent / Halogen
120 V~ Dimmer
Rated at 120 V~ 60 Hz 600 W
Important Notes
Please read before installing.
1. Note: Use only with permanently-installed 120 V~ incandescent or
halogen fixtures. To avoid overheating and possible damage to other
equipment, do not use to control receptacles, fluorescent lighting fixtures,
motor-driven appliances, or transformer-supplied appliances.
2. Install in accordance with all national and local electrical codes.
3. Only one dimmer can be used in a 3-way circuit.
4. When no "grounding means" exist within the wallbox then the
NEC 2008, Article 404.9 allows a dimmer without a grounding connec-
®
tion to be installed as a replacement, as long as a plastic, noncombustible
wallplate is used. For this type of installation, cap or remove the green
ground wire on the dimmer and use an appropriate wallplate such as
Claro or Fassada series wallplates by Lutron .
® ® ®
5. For new installations, install a test switch before installing the dimmer.
6. Protect dimmer from dust and dirt when painting or spackling.
7. Recommended minimum load is 40 W.
8. It is normal for the dimmer to feel warm to the touch during operation.
9. Clean dimmer with a soft damp cloth only. Do not use any chemical
cleaners.
Multigang Installations
When installing more than one control in the same
wallbox, it may be necessary to remove all inner
side sections prior to wiring (see diagram). If pre-
installed, remove the Lutron wallplate and
wallplate adapter from dimmer. Using pliers, bend
side section up and down until it breaks off.
Repeat for each side section to be removed.
Removal of dimmer side sections reduces maxi-
mum load capacity. Refer to chart below for maxi-
mum dimmer capacity.
Dimmer Capacity Chart
Dimmer Rating No sides
removed
600 W 600 W
Technical Assistance
If you have questions concerning the installation or operation of this product, call the
Lutron Technical Support Center. Please provide exact model number when calling.
U.S.A. and Canada (24 hrs/7days)
1.800.523.9466
Other countries 8am – 8pm ET
+1.610.282.3800
Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service,
return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE
YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULT-
ING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CON-
SEQUENTIAL DAMAGES. LUTRON'S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE,
SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or
limitation of incidental or consequential damages, or limitation on
how long an implied warranty may last, so the above limitations
may not apply to you.
This product may be covered by one or more of the following •
U.S. patents: 4,835,816; 4,939,383, and corresponding foreign
patents. Lutron, Fassada, and Claro are registered trademarks of
•
Lutron Electronics Co., Inc. NEC is a registered trademark of
National Fire Protection Association, Quincy, Massachusetts.
© 2008 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Made and printed in U.S.A.
4/08 P/N 030-990-03 Rev. B
Lutron Technical Support Center
English
Installation
Models:
1
D-603PG
LG-603PG
S-603PG
2
3
Do Not Remove
Outside Sections
Each Control Has Inside Middle Control Has Two Single-Pole:
Sections Removed Side Sections Removed
Insulated wires connected
to two screws of the same
1 side 2 sides
color.
removed removed
500 W 400 W
4
Important Note: Your wall switch may have one continuous wire attached to the same
screw (see illustrations below for examples). Tape these two wires together before dis-
connecting.
Fax +1.610.282.6311
http://www.lutron.com
Easy-to-follow Easy-to-follow
•
Instructions Instructions
Instructions à Instructions à
•
Suivre Suivre
030-990-03 030-990-03
1.800.523.9466
Turning OFF Power.
• Turn power OFF at circuit breaker (or remove fuse).
Warning: Before proceeding, verify that
power to the switch is OFF.
Otherwise, death or serious injury
could result.
Removing Wallplate and Switch.
• Remove wallplate and switch mounting screws.
• Carefully remove switch from wall (do not remove wires).
Identifying the Type of Circuit.
Different-colored screw (COMMON).
Actual location may vary.
Or
Ground (bare
copper or
green wire)
Ground (bare copper or
green wire)
3-Way:
Tape
Insulated wires connected to three screws. Two
screws are the same color and the other is a dif-
Or
ferent color (COMMON), not green. Tape the wire
that is connected to the different color screw to
identify it when rewiring.
Disconnecting Switch Wires.
One wire in the
backwired hole
and one to the
screw.
Tape
24 hrs / 7 days www.lutron.com
5
Wiring the Dimmer.
• For installations involving more than one control in a wallbox, refer to the
section on Multigang Installations before beginning.
Helpful Hints:
1. The red/white wire is not used in a single-pole application. Twist a wire
connector onto this wire if the Dimmer is used for a single-pole application.
2. Dimmer wire locations will vary by product. Reference wires by color, not location.
5a - Single-Pole Wiring
Red
Black
Green
Ground
Red/White
Red
Black
Green
120 V~
60 Hz
Light
Ground
Red/White
5b - 3-Way Wiring
Red
Tape
Black
Green
Red/White
Black Red
Red/White
Green
One continuous
wire to the
Dimmer 3-Way Switch
120 V~
screw.
60 Hz
Ground
6
Mounting Dimmer to Wallbox.
• Form wires carefully into the wallbox, mount and align dimmer.
• Install wallplate.
Screw Terminals:
Turn screws to
Start screws.
loosen.
For D-603PG: To install a traditional
Push-In Terminals:
style wallplate, firmly pull the rotary
Insert screwdriver. Pull
knob to remove it. Install the
wire out.
wallplate and re-attach the knob.
7
Turning ON Power.
• Turn power ON at circuit breaker (or replace fuse).
• Connect the green dimmer ground
wire to the bare copper or green
ground wire in the wallbox. (See
Important Note 4.)
• Connect the black dimmer wire to
one of the wires removed from the
switch. If you had taped together
two wires (see step 4), connect both
wires to the black dimmer wire and
remove the tape.
• Connect the red dimmer wire to the
other wire removed from the
switch.
• Twist a wire connector onto the
red/white dimmer wire; this wire
does not get connected.
This operation has now been completed.
Note: Only one dimmer can be used
in a 3-way circuit.
• Connect the green dimmer ground
wire to the bare copper or green
ground wire in the wallbox. (See
Important Note 4.)
• Connect the black dimmer wire to
the wire removed from the differ-
ent-colored screw on the switch
(taped wire). If you had taped
together two wires (see step 4),
connect both wires to the black
dimmer wire. Remove tape from
Ground
wire.
• Connect the red dimmer wire to
one of the remaining wires
removed from the switch.
• Connect the red/white dimmer
wire to the other remaining wire
removed from the switch.
Light
This operation has now been completed.
Align dimmer and
tighten screws.