Warn 80371 Instructions De Montage
Warn 80371 Instructions De Montage

Warn 80371 Instructions De Montage

Kit de montage pour treuil de vtt

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Your safety, and the safety of others, is very important. To help you make informed decisions about
safety, we have provided installation and operating instructions and other information on labels and in
this guide. This information alerts you to potential hazards that could hurt you or others. It is not
possible to warn you about all potential hazards associated with this product, you must use your own
good judgment.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT
DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING
INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid
personal injury or death. WARNING and CAUTION are signal words that identify the level of hazard.
These signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow
recommendations.
do not follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize
genera l information worthy of special attention.
Failure to observe these instructions could lead to severe injury or death.
Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical
wires, and other objects are not punctured or damaged when / if drilling on the vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and relocate any objects that may be
damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or
personal injury.
Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips.
Flying chips can cause eye injury.
Always use extreme caution when cutting and trimming during fitting.
Always remove jewelry and wear eye protection.
Never lean over battery while making connections.
Never route electrical cables:
Across any sharp edges.
Through or near moving parts.
Near parts that become hot.
Always insulate and protect all exposed wiring and electrical terminals.
Always install terminal boots as directed in installation instructions.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and operation.
Always tighten all nuts and bolts securely, per the installation and operation.
Always perform regular inspections and maintenance on the winch, winch mount and related hardware.
Never operate this WARN product with damaged or missing parts.
INSTALLATION INSTRUCTIONS
WINCH MOUNTING KIT
Application: 2009 Polaris Ranger XP, HD
CAUTION signals a hazard that may cause minor to moderate injury, if you
WARNING
INJURY HAZARD
PAGE 1
Part Number:
80371
80372A0

Publicité

Table des Matières
loading

Sommaire des Matières pour Warn 80371

  • Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.
  • Page 2: Before You Begin

    Equipment Damage Always refer to the Installation and Specification Guide, supplied in the winch kit, for all wiring schematics and specific details on how to wire this WARN product to your vehicle. Read installation and operating instructions thoroughly. I. BEFORE YOU BEGIN Before you begin disconnect the positive battery lead from the battery.
  • Page 3: Parts List

    V. PARTS LIST Part Number Description 80373 Brkt, Winch Polaris Ranger MY09 79464 M12x1.75x25mm Hex Flangehead Capscrew 79465 M12x1.75 Hex Flange Nut with insert 69771 M8x1.25x25mm Hex Flangehead Capscrew 71588 M8x1.25 Hex Flange Nut with insert 79461 M10x1.25x20mm Hex Flangehead Capscrew 79463 M10x1.25 Hex Nut with insert 34402...
  • Page 4 VI. INSTALLATION 1. Remove top and middle grille plates from Remove top and middle grille plates vehicle, as shown in Figure 1, using a #27 Torx screwdriver to loosen the hardware. Use a 13mm socket to remove the bottom bumper mounting hardware.
  • Page 5 INSTALLATION CONT. 4. Mount the winch assembly to the front bumper, as shown in Figure 4, using four M12 x 1.75 x 25mm flangehead capscrews and flange nuts provided in the hardware kit. Use a 16mm wrench and 18mm socket to loosely secure in place at this time.
  • Page 6 Figure 7 WARNING READ THE VEHICLE’S OPERATOR MANUAL, WINCH OPERATOR MANUAL, AND ALL WARN- ING LABELS PRIOR TO OPERATION OF UTV AND WINCH. THE WINCH MOUNTING PLATE INSTALLATION IS NOW COMPLETE. • Wire winch according to instructions found in winch kit.
  • Page 7: Maintenance/Care

    WARNING FAILURE TO SECURELY TIGHTEN ALL BOLTS ON THE WINCH PLATE, WINCH, AND FAIRLEAD CAN RESULT IN PRODUCT FAILURE WHICH MAY RESULT IN VEHICLE DAMAGE AND OPERATOR INJURY OR DEATH. DOUBLE CHECK THAT ALL BOLTS ARE SECURELY TIGHTENED PRIOR TO USE. VII.
  • Page 8: Kit De Montage Pour Treuil De Vtt

    Serrez toujours bien les écrous et les boulons conformément aux instructions d’installation et d’utilisation. Effectuez toujours régulièrement les inspections et l’entretien du treuil, de son kit de montage et du matériel de montage connexe. Ne faites jamais fonctionner ce produit WARN avec des pièces endommagées ou manquantes. PAGE 8 80372A0...
  • Page 9: Avant De Commencer

    Reportez-vous toujours au Guide d’installation et de spécification, fourni dans le kit de treuil, pour tous les schémas de câblage et des informations détaillées concernant la façon de brancher ce produit WARN sur votre véhicule. Veuillez lire attentivement les instructions concernant l’installation et l’utilisation.
  • Page 10: Liste Des Pièces

    V. LISTE DES PIÈCES Référence Qté Description 80373 Support, treuil Polaris Ranger modèle 09 79464 Vis à tête hexagonale à épaulement M12x1,75x25 mm 79465 Écrou hexagonal à épaulement M12x1,75 avec insert 69771 Vis à tête hexagonale à épaulement M8x1,25x25 mm 71588 Écrou hexagonal à...
  • Page 11 VI. INSTALLATION 1. Retirer du véhicule les plaques de grille du Retirer les plaques de grille du haut et du milieu haut et du milieu, tel qu’indiqué à la figure 1. Utiliser un tournevis Torx n° 27 pour desserrer le matériel de fixation. Retirer le matériel de fixation du pare-chocs inférieur à...
  • Page 12: Installation (Suite)

    INSTALLATION (SUITE) 4. Monter le treuil sur le pare-chocs avant, tel qu’illustré à la figure 4, à l’aide de quatre vis à tête à épaulement M12 x 1,75 x 25 mm et d’écrous à épaulement fournis dans le kit de matériel.
  • Page 13 INSTALLATION (SUITE) 7. À l’aide du matériel Torx d’origine, réinstaller la plaque de grille supérieure. Remarque : la plaque de grille avant ne sera plus utilisée. La figure 7 montre l’installation finale du treuil RT/XT 40 avec le pare-chocs en place. Figure 7 AVERTISSEMENT LISEZ LES MANUELS DE L’UTILISATEUR DU...
  • Page 14: Maintenance, Entretien

    AVERTISSEMENT LE FAIT DE NE PAS SERRER SOLIDEMENT TOUS LES BOULONS DU TREUIL, DE LA PLAQUE DE TREUIL ET DU GUIDE-CÂBLE PEUT ENTRAÎNER UNE DÉFAILLANCE DU PRODUIT, CE QUI PEUT ENDOMMAGER LE VÉHICULE ET PROVOQUER DES BLESSURES OU LA MORT DE L’OPÉRATEUR.

Table des Matières