Table des Matières
Publicité
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
as follows:
1. pull out the plug from the wall socket or turn the
thermostat knob to the ÇOÈ setting;
2. remove any stored food, wrap it in several layers
of newspaper and put it in a cool place;
3. leave the door open;
4. when defrosting is completed, dry the interior
thoroughly;
5. turn the thermostat knob back to the required
setting or replace the plug in the power socket.
6. After two or three hours, reload the previously
removed food into the compartment.
Important:
Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.
Do not use a maechanical device or any artificial
means to speed up the thawing process other
than those recommended by the manufacturer.
A temperature rise of the frozen food packs,
during defrosting, may shorten their safe
storage life.
CUSTOMER SERVICE AND SPARE PARTS
If the appliance is not functioning properly, check
that:
¥
the plug is firmly in the wall socket and the mains
power switch is on;
¥
there is an electricity supply (find out by plugging
in another appliance);
¥
the thermostat knob is in the correct position.
¥
If there are water drops on the bottom of the
cabinet, check that the defrost water drain
30
opening is not obstructed (see ÒDefrostingÓ
section).
¥
If your appliance is still not working properly after
making the above checks, contact the nearest
service centre.
To obtain fast service, it is essential that when you
apply for it you specify the model and serial number
of your appliance which can be found on the
guarantee certificate or on the rating plate located
inside the appliance, on the bottom left-hand side.
RENSEIGNEMENTS POUR LÕƒLIMINATION
DES MATƒRIAUX DÕEMBALLAGE
Tous les matŽriaux et les accessoires utilisŽs pour
emballer nos grands ŽlectromŽnagers, sauf ceux qui
sont en bois recyclables et peuvent donc se
rŽcupŽrer.
Voici ce que nous vous conseillons:
¥
DŽposez les emballages en papier, en carton et
en carton ondulŽ aux endroits prŽvus pour le
ramassage de ce genre de matŽriau.
¥
Mettez les piŽces en plastique dans les
conteneurs prŽvus ˆ cet effet. Si ce genre de
conteneurs nÕexistent pas encore ˆ lÕendroit o•
vous habitez, vous pouvez Žliminer les matŽriaux
en question en les mettant dans les ordures
mŽnag•res.
Pour les emballages de mati•res plastiques
recyclables, par example:
SOMMAIRE
Avertissements et conseils importants .................................................................................................13
Renseignements pour lÕŽlimination des matŽriaux dÕemballage ........................................................15
Utilisation/ Nettoyage - Mise en service - RŽglage de la tempŽrature - CongŽlation - Conservation des ..
produits surgelŽs - DŽcongŽlation -Gla•ons..............................................................................................16
Utilisation/ RŽfrigŽration - Tablettes amovibles - Positionnement des balconnets de la contre-porte ......
Calendrier de congŽlation..........................................................................................................................17
Conseils / Conseils pour la rŽfrigeration - Conseils pour la congŽlation - Conseils pour la surgŽlation ..18
Entretien / Nettoyage - Arr•t prolongŽ - Changement de lÕampoule........................................................19
Entretien /DŽgivrage - Anomalie de fonctionnement ............................................................................20
Innformations techniques / Installation / Emplacement........................................................................21
Installation / Branchement Žlectrique - Entretoises postŽrieures.............................................................22
Installation / RŽversibilitŽ de la porte ......................................................................................................23
Les exemples reportent les symboles suivants:
02**
05
06
PE
PP
PS
PE pour polyŽthyl•ne** 02 = ^ PE-HD; 04 = ^ PE-LD
PP pour le polypropyl•ne
PS pour le polystyr•ne
PIƒCES EN MATIƒRE PLASTIQUE
Pour faciliter lÕŽlimination et :ou le recyclage des
matŽriaux, la plupart des pi•ces de lÕappareil ont
une contremarque qui en facilite lÕindentification.
SAN
ABS
PS
15
Publicité
Table des Matières
