Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
CAUTION:
Read this manual
carefully before operating your new
Cannon Downrigger.
Retain for future reference.
TERMINATING THE DOWNRIGGER CABLE
TERMINATING THE DOWNRIGGER CABLE
NOTE: Use only straight cable when routing through the terminator. Worn or kinked cable can be stressed and may
break prematurely when retrieving trolling weights.
NOTE: Use only straight cable when routing through the terminator. Worn or kinked cable can be stressed and may
NOTE: A set of pliers with wire cutters is recommended for this part of setup.
break prematurely when retrieving trolling weights.
NOTE: A set of pliers with wire cutters is recommended for this part of setup.
1. Unwind about 2 feet of cable and
thread through the rubber cushion.
1. Unwind about 2 feet of cable and
Attach Swivel Snap to terminator.
thread through the rubber cushion.
Attach Swivel Snap to terminator.
2. Examine the top of the terminator
and note the order shown in the
2. Examine the top of the terminator
detail to run cable.
and note the order shown in the
detail to run cable.
3. Lead and pull six inches of cable
through HOLE A. Thread cable
3. Lead and pull six inches of cable
through swivel, then up into bottom
through HOLE A. Thread cable
of the terminator. Lead cable out of
through swivel, then up into bottom
HOLE B and into HOLE C. Push the
of the terminator. Lead cable out of
cable until its end touches the inside
HOLE B and into HOLE C. Push the
of the terminator hook. Tighten cable
cable until its end touches the inside
by squeezing terminator until it snaps
of the terminator hook. Tighten cable
shut. Then pull at top and bottom
by squeezing terminator until it snaps
until drawn tight. Make sure that the
shut. Then pull at top and bottom
cable threads the hook.
until drawn tight. Make sure that the
NOTE: Use only straight cable, not kinked cable.
cable threads the hook.
NOTE: Use only straight cable, not kinked cable.
4. Slide the cushion over the top of the terminator and give it a test pull. The cable is now set to attach a Cannon Flash Weight™.
cannondownriggers.com
4. Slide the cushion over the top of the terminator and give it a test pull. The cable is now set to attach a Cannon Flash Weight™.
MINI-TROLL MANUAL DOWNRIGGER
MOUNTING TO YOUR BOAT
Depending on boat application, the spacer
block (supplied) may be required. To attach
the spacer block to the main frame, simply slide
the dovetail shaped tab of the block into the
matching recess in the frame. Make sure that
the holes in the block face down.
Transom Mount
Depending on transom width, a wood block
may be required to allow the rigger to clamp
properly.
Gunwale Mount*
On thin-walled aluminum boats, it is
recommended that a wood block be used on
the inside of the boat. This will distribute
the clamping force to a larger area to prevent
possible boat damage. Depending on rail
overhang, a wood block may also be required
on the outside of the boat.
*We recommend you mount Mini-Troll off the transom of your boat (if
possible), so that the weight is being pulled directly behind the downrigger.
Mounting your Mini-Troll the gunwale is not recommended as lateral stress
on the frame may cause cracking.
Step 1.
Step 1.
Cable
Cable
Rubber
Cushion
Rubber
Cushion
Step 3.
Step 3.
HOLE A
HOLE B
HOLE A
HOLE B
HOLE C
HOLE C
Swivel
Swivel
MODEL #1901200
Step 2.
Step 2.
Snap
&
Swivel
Snap
&
Swivel
Step 4.
Step 4.
©2015 Johnson Outdoors Marine Electronics, Inc.
Spacer Block
Transom Mount
Gunwale Mount
A. CABLE
IN
C. CABLE
A. CABLE
IN
IN
C. CABLE
IN
B. CABLE
OUT
B. CABLE
OUT
Publicité
Manuels Connexes pour Cannon 1901200
Sommaire des Matières pour Cannon 1901200
- Page 1 NOTE: Use only straight cable, not kinked cable. 4. Slide the cushion over the top of the terminator and give it a test pull. The cable is now set to attach a Cannon Flash Weight™. cannondownriggers.com ©2015 Johnson Outdoors Marine Electronics, Inc.
- Page 2 Fishing Line Câble Line Release Weight Figure 1 Figure 2 Figure 3 Figure 4 Cannon Consumer & Technical Service 121 Power Drive Johnson Outdoors Marine Electronics, Inc. Mankato, MN 56001 cannondownriggers.com PO Box 8129 Phone (800) 227-6433 A Johnson Outdoors Company ©2015 Johnson Outdoors Marine Electronics, Inc.
- Page 3 MINI-TROLL MANUAL DOWNRIGGER This page provides Cannon® WEEE compliance disassembly instructions. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.
- Page 4 AFTER THE APPLICABLE WARRANTY PERIOD After the applicable warranty period, or, if one of the above exclusions applies, Cannon® products will be repaired for a charge of parts plus labor. All factory repairs, after the applicable warranty period, carry a 90-Day Limited Warranty, subject to the exclusions and limitations stated above.
- Page 5 Tête pivotante REMARQUE: n’utilisez qu’un câble droit, non tordu. 4. Glissez le coussin par-dessus le terminateur et donnez-lui un tir d’essai. Le câble est maintenant prêt à fi xer au Cannon Flash Weight™. cannondownriggers.com ©2015 Johnson Outdoors Marine Electronics, Inc.
- Page 6 Câble Dispositif de Dévidage Poid Figure 1 Figure 2 Figure 3 Figure 4 Cannon Consumer & Technical Service 121 Power Drive Johnson Outdoors Marine Electronics, Inc. Mankato, MN 56001 cannondownriggers.com PO Box 8129 Phone (800) 227-6433 A Johnson Outdoors Company ©2015 Johnson Outdoors Marine Electronics, Inc.