Publicité
Les langues disponibles
Les langues disponibles
PLuMbIng EquIPMEnt
Water line: arrange your shower box with the water supply line and coupling for the showerhead. The
coupling must be above the ceiling. (Fig. 1). 10 litres of water per minute is enough for the showerhead
to work.
Gb
ELECtRICAL EquIPMEnt
• Power connection: arrange your shower box with the electrical connection for the showerhead LED
lights, placing it above the false ceiling (Fig. 1). Warning: The electrician must use a power cable thatis
two-pole, 1 mm2 size, outside diameter between 5 and 13 mm.
•The transformer 7V ~ / 230V ~ – 50/60 Hz must be installed outside the shower box in a safe place (Fig.
1).
tuRnIng thE LED LIghtS on
LEDs are devices that generate monochromatic light. For them to work properly, they need only a small
amount of power supply and voltage and therefore use little energy and run on low temperatures.
The LEDs are activated when with an interrupter (not furnished) that the electrician must properly
predispose in the environment bath.
FALSE CEILIng
•Once the electrical and hydraulic systems are hooked up, realise the false ceiling with suitable
reinforcement, as when mounting a chandelier, and make sure it is perfectly level.
•Keep a distance of at least 12 cm between the ceiling and the false ceiling (Fig.1). Position the template,
mark with a pencil the 4 attachment holes and the central beak-through that will house the electrical
and hydraulic parts of the showerhead (Fig.2).
•Make the 4 attachment holes having a 10 mm diameter
• Make the beak-through (Fig.3)
•Insert the 4 expansion screws and make sure that they are placed accurately (Fig.4).
ShoWERhEAD InStALLAtIon
•Open the bipolar terminal box IP68 (7) and attach the electrical connections that go to the transformer
(Fig.5).
•Connect one end of the hose (9) to the shower head (1) and the other end to the water supply line on the
wall (Fig.6).
If there is a ½"F wall connection, use the adaptor (14) ½"M × ½"M that is included.
•Lay the showerhead in correspondence of the four expansion screws that were previously inserted in the
false ceiling, and tighten the 4 screws (10) included (Fig.7) until the showerhead is properly fitted to the
false ceiling (Fig.8). Make sure that the screws are fully tightened, about 16 full turns every screw (Fig.7).
ELECtRICAL EquIPMEnt - tEChnICAL SPECIFICAtIonS
1. Electric connection
Absorbed electricity 0,1
2. Electric cable
3. Cube Light 260x260 mm
4. OKI Light Ø 280 mm
5. Safety Transformer
6. Grade of protection
7. Safety mark
The electrical systems must be carried out by a qualified technician in accordance with the national and
international laws in force.
12
LiGHT
oki & Cube
220/230V ~ – 50/60 Hz - max 20w
A class of protection II
bipolar, 1 mm² size, outside diameter 5 mm to
13 mm (supplied by customer)
4 low voltage LEDs
4 low voltage LEDs
7V ~/ 230V~ – 50/60 Hz to be installed outside the
safety area (in compliance with standard DIN VDE
0100, part 107 – according to prescription CEI 64/8)
IP x 5 (excluding transformer)
CE
All manuals and user guides at all-guides.com
LED REPLACEMEnt
It is not necessary to remove the showerhead from the false ceiling to replace LEDs that are not
working. Attention, to only use lamps to specific LED.
Fig.9 unscrew the chrome ring nut
Fig.10 remove the chrome ring nut
Fig.11 pull the LED from the showerhead body
Fig.12 release the LED being replaced
Fig.13 connect the new LED
Fig.14 insert the LED in its housing
Fig.15 re-screw the safety ring nutdis 18
CLEAnIng
Dear Customer,
Congratulations for choosing a Bossini product and we thank you for the trust you have given us. To keep
the material's appearance as long as possible, a few guidelines must be followed.
Cleaning metal parts: water contains calcium that deposits on surfaces and forms unpleasant spots.
For routine cleaning, simply use a damp cloth with a little soap, rinse and dry. Calcium spots can therefore
be avoided by drying after use.
Important note: Using only a soap-based detergent is recommended. Never use abrasive detergents or
disinfectants or those containing alcohol, hydrochloric acid or phosphoric acid.
Cleaning the rubber nozzles: the showerhead is equipped with the "Easy-Clean" system with silicon
nozzles. Calcium is a shower's worst enemy and that is why Bossini proposes the
Easy-Clean" system. These silicon nozzles are extremely heatresistant and with hot water they dilate,
thus detaching the first layer of calcium. Moreover, periodically bending the silicon nozzles manually
easily gets rid of calcium. With one simple gesture, your shower is always perfect.
Dear Customer, we would like to remind you that the warranty on our product's surface is not valid if
the material undergoes treatment different than that suggested. the warranty does not cover any
damage due to deposits of calcium or impurities.
WARRAnty tERMS
Dear Customer,
We congratulate you and thank you for choosing a Bossini quality product
The product is covered by 2 Years warranty against any defects due to manufacturing faults.
the warranty does not cover damages caused by improper installation or use, neglect, incorrect
plumbing, normal fair wear and tear, damages caused by limescale deposits or impurities, the use of
detergents and maintenance products other than those specifically recommended in our instructions
manual. Furthermore Bossini is not responsible for labour costs and/or damages, whether accidental or
consequent to the installation, repairing or replacement of the product.
The request for replacement under the terms of this warranty must be made in a letter setting out the date
and place of purchase and giving a brief explanation of the problem. The letter must be received by us
within the warranty period and must be accompanied by proof of the purchase date (e.g. a receipt). The
warranty only covers production faults / defects and is strictly limited to the repair or free replacement of
the parts which are recognised to be defective. The defective parts have to be returned to Bossini carriage
free with a report describing the defect. Bossini reserves the right to inspect the part alleged to be faulty
or defective and to evaluate the applicability of the warranty terms.
the warranty period commences on the date the product is purchased, evidenced by the relevant
purchase document (e.g. receipt, invoice, cash voucher) and it is unrenewable.
For further information please contact Bossini or its distributor.
LiGHT
oki & Cube
Gb
13
Publicité
