Publicité
Les langues disponibles
Les langues disponibles
programmable effect parameters set, when all the BEAT
LEDs are off. Use the Beat-Sync. Selection buttons to change
the beat-sync effect set.
Note : When we push one of this button, you cannot change
effect parameters in using TIME FX & RATIO FX buttons. You
must to use beat buttons to change paramterers.
15. PITCH SLIDER
Use this fader to increase or decrease the speed of the track.
16. PITCH BEND BUTTONS
When 2 CD players are playing a CD, the pitch bend function
allows the positioning of the bass beats to be matched after
the pitch has been matched. The pitch will automatically rise
when the + button is pressed and return to the original pitch
when it is released.
The pitch will drop while the - button is pressed. By changing
the pitch in this way, the positioning of the beats can be
matched.
17. PITCH RANGE ADJUSTMENT BUTTON
When pitch function has been turned on, holding the button
then tapping the PITCH BEND + button to change the pitch
percentage the PITCH SLIDER will react to . The PITCH
BUTTON's LED will indicate which pitch percentage mode
you are in, glowing red for 4%, flashing red for 8%,glowing
blue for 16%, or flashing blue for 100%.
18. BPM BUTTON
Use to select between display of pitch vlaue or display of BPM
value ( automatic value ).
19. TIME BUTTON
The TIME button will switch the time value described in the
time meter between elapsed play time, track remaining time,
and total remaining time.
20. SGL ( SINGLE )/CTN ( CONTINU )
This function allows you to choose between single track play
or continuous track play (all tracks in order).
21. RELOOP BUTTON
This button is used to start the last saved seamless loop. To
finish the loop, press the OUT / EXIT button..
22. OUT / EXIT BUTTON
When you press this button, you set the end point of the
seamless loop and you start the loop. To finish the loop, press
again this button.
23. IN BUTTON
This button allows you to set the cue point without stopping
the playback. This button also sets the beginning of the
seamless loop.
24. TAP BUTTON
Tap the BE.AT COUNTER to the rhythm of the music at least
3 times, for more accurate reading tap it between 6 and 10
times.
25. WHEELS
3 functions :
In pause mode, this wheel is used to make frame to
-
frame research.
-
During the playback :
•
In normal mode, the wheel is used like the
pitch bend buttons
•
In scratch mode, this wheel is used to scratch
like with a turntable ( touch the wheels in the
central part ).
Note : In the normal mode ( when the wheel is used to adjust
the speed of the tracke ) and if the holf button is light, the
wheel will operating like the pitch slider. To find back the
normal speed of the track, push the pitch on/off button (13)
two times.
26. BANK BUTTONS
These three buttons have two functions :
-
CUE points backup :
To save a CUE point, you must to push the memory
button then push the in button to select the desired cue
point. After select the bank where you want to save the
cue point.
Samplr memory :
-
The sampler memories are just loop make from the cue
point you saved ( 7s for each memory ). For example, if
you have save a cue point in the memory 1, you sample
will be a loop of 7s from this cue point.
To read the sample, push the sampler button and select the
bank you want. If you are in the single mode, the sample will
be read one time. If you are in the continu mode, the sample
will be read in loop until you push the sampler button.
27. SAMPLER BUTTON
Used to read the sample you saved. To read the sample,
push the sampler button and select the bank you want. If you
are in the single mode, the sample will be read one time. If
you are in the continu mode, the sample will be read in loop
until you push the sampler button.
Note :
-
Samples will be save even you eject the cd. To clean the
samples, you must to save in it place or you must to
switch your cd player off.
The TIME FX button (1) is used to adjust the speed of
the track ( If the HOLD button is on ) or like the pitch
bend button ( if the HOLD button is off ) & the RATIO FX
button (2) is used to adjust the level of the sample. The
wheel operate just in the scratch mode ( and if the cd is
eject ).Sampler button
28. MEMORY BUTTON
This button is used to memorise cue points ( 3 memories ).
It's used to save sample to ( see description before )
29. PLAY/PAUSE BUTTON
Each time you press the PLAY/PAUSE button, the operation
changes from play to pause or from pause to play..
30. CUE BUTTON
Pressing the CUE button during play provides a return to the
position at which play was started
31. LCD DISPLAY
This diplay shows you time, pitch value ( or BPM value ), level
of the anti-shock memory, ...
32. SEARCH WHEELS
Turn this wheel clockwise to scan in the forward direction.
Turn this wheel counter clockwise to scan in the reverse
direction The scanning speeds up when the shuttle dial is
turned faster
33. OPEN/CLOSE BUTTON
Press to load or eject disk. Each press will open or close the
disk tray.
NOTE: disc holder will not open unless stop or pause button
has been pushed first.
BOITIER CD PANNEAU AVANT :
34. CD TRAY
Placez le disque sur le tiroir.
35. OPEN/CLOSE BUTTON
Press to load or eject disk. Each press will open or close the
disk tray.
NOTE: disc holder will not open unless stop or pause button
has been pushed first
36. POWER SWITCH ( ON / OFF )
Press the power switch to turn the unit on. To switch the
POWER off press the POWER switch again.
8
Publicité
