Publicité
Les langues disponibles
Les langues disponibles
Stopping playback.
There are two ways to stop playback :
-
Press the PLAY / PAUSE button during
the playback to pause at the point.
Press the CUE button during playback to
return to the CUE point and enter pause
condition ( Back CUE ).
Modifier la vitesse de la musique.
-
There are three tools for matching the
BPM of two CDs.
1)
Pitch slider
2)
Pitch bend buttons
3)
wheel
1)
pitch slider
To adjust the BPM by sliding the pitch
potentiometer up or down, press the pitch
button to turn on the pitch adjustement function
before use.
Slide the pitch potentiometer up to decrease
BPM or down to increase the BPM. The
adjustement range is +/-4%, +/-8%, +/-16 or
+/-100%
2)
Pitch bend buttons
When 2 CD players are playing a CD, the
pitch bend function allows the positioning of the
bass beats to be matched after the pitch has
been matched. The pitch will automatically rise
when the + button is pressed and return to the
original pitch when it is released.
The pitch will drop while the - button is pressed.
By changing the pitch in this way, the
positioning of the beats can be matched.
3)
Wheel
If the HOLD function is on :
Turn the wheel in the clockwise direction to
increase the BPM or the opposite direction to
decrease the BPM. Faster you turn the wheel,
more the BPM value change. The adjustment
range is choose in using the pitch selector
button
If the HOLD function is off :
The wheel is used like the pitch bend buttons
Seamless Loop play
- Press the IN button to set the loop start
point A, The indicator will flash on the
LCD.
- Press the OUT / EXIT button to set the
loop end point B, after the point B is set,
the playback will enter the loop play from
A to B repeatedly. The indicator on the
display lights
- Press the OUT / EXIT button again, the
loop play function is canceled, the loop
indicator goes out..
The player will work normally when the main unit is
mounted with the front panel at within 15 degrees of
the vertical plane. If the unit is tilted excessively,
discs may not be loaded or unloaded properly.
Frame search
- Frame search is a function for monitoring the
sound at a certain section of the disc and
manually change the position. Searching is
used to set play start points with precision.
- Turn the JOG dial while in pause or CUE
mode to begin searching. The sound for one
revolution of the disc is output repeatedly.
The point at which the sound starts is
indicated on the LCD.
- When the JOG dial is turned, the point from
which the sound is output moves a number
of frames corresponding to the number of
clicks, and the time display on LCD also
changes.
- The search point moves in the forward
direction when the JOG dial is turned
clockwise, in the reverse direction when
the JOG dial is turned counterclockwise.
Scanning ( fast forward / fast backward )
-
Scanning is a function for moving quickly
forward or
button is rotated.
-
This unit supports 3 differents speeds
according to the rotating angle of the search
button
- Turn the search button dial to begin
scanning. The disc moves rapidly foraward
or backward and the sound is output. The
current scan point is indicated on the LCD.
- Turn the search button dial clockwise to scan
in the forward direction, counterclockwise to
scan in the reverse direction.
Relay function
Put the two side in the single mode
-
Start the playback in one side
-
At the end of the track, the player will be
enter in the pause mode and go the next
track ( in pause mode ). The playback will
be start in the other side.
-
The relay function will be continu until you
must to stop it.
In loading the good cd, you can make your
-
prog order.
If you save a cue point, the playback will
-
start from this point.
NOTE:
The relay function will operating well only if you plug
the two side on the same mixer or on the same
power amplifier.
Version
You can display the version by turning the
-
power on and turn the SEARCH wheel
clockwise then the LCD will display the
version like "01 03 02".
Installing the Unit
1.
Place your unit on a flat surface or mount
it in a secure rack mount case.
2.
Be sure the player is mounted in a well
ventilated area where it will not be
exposed to direct sunlight, high
temperatures, or high humidity.
3.
Try to place the unit as far as possible
from TVs and tuners, as the unit may cause undesirable
interference.
CAUTION:
The control panel's LCD's are designed to be clearly
visible within the angles shown in Figure 2. Mount
the control unit so that the visual angle is within this
range.
10
backward when the search
Publicité
