LEGRAND Wattstopper LMRC-111-16M Guide De Démarrage Rapide

No: 28168 – 06/21 rev. 4
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMRC-111-16M
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
LMRC-111-16M -U is BAA and TAA compliant (Product produced in the U.S.)
IMPORTANT
SAFEGUARDS
When using electrical equipment, basic safety
precautions should always be followed including the
following:
a. READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b. Do not use outdoors.
c. Do not mount near gas or electric heaters.
d. Equipment should be mounted in locations and
at heights where it will not readily be subjected
to tampering by unauthorized personnel.
e. The use of accessory equipment not
recommended by the manufacturer may cause
an unsafe condition.
f. Do not use this equipment for other than
intended use.
g. Installation should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS
CAUTION: TO CONNECT A COMPUTER
TO THE DLM LOCAL NETWORK USE THE
LMCI-100. NEVER CONNECT THE DLM
LOCAL NETWORK TO AN ETHERNET
PORT – IT MAY DAMAGE COMPUTERS
AND OTHER CONNECTED EQUIPMENT.
Wattstopper
DLM Single Relay 0–10V Dimming Room Controller with Metering
DLM relais simple contrôleur de pièce de gradation 0–10 V avec mesure
Relé simple DLM controlador de regulación de habitación de 0 a 10 V con medición
Quick Start Guide • Guide de démarrage rapide • Guía de inicio rápido
Input Voltage ..........................................................................120/277VAC, 50/60Hz
Relay rated for up to:
Incandescent ............................................................................ 16A @ 120VAC
Ballast ............................................................................... 16A @ 120/277VAC
E-ballast ............................................................................ 16A @ 120/277VAC
Output to DLM Local Network ..............................................up to 150mA @ 24VDC
Class 1 & 2 Dimming Output, 0–10V sinks up to 50mA per channel
Connection to the DLM Local Network .................................................2 RJ-45 ports
DLM Local Network Characteristics when using LMRC-111-16M:
Provides low voltage power over Cat 5e cable (LMRJ); max current 800mA.
Supports up to 64 load addresses, 48 communicating devices, and free
topology up to 1,000' max. If combined with LMRC/LMPL-100 series load
controllers, a maximum of 4 controllers can be used per room. All other
LMRC/LMPL series can support more than 4 per room.
Metering capability in LMRC-111-16M provides power monitoring within +/-2% of the
true value.
Power monitoring capability when used with Wattstopper compatible Network
Management Software (DLM Dashboard, Niagara N4 or BACnet compliant BMS).
Environment:
Operating Temperature ............................................. 32° to 131°F (0° to 55°C)
Storage Temperature ............................................... 23° to 176°F (-5° to 80°C)
Relative Humidity ................................................... 5 to 95% (non condensing)
UL 2043 Plenum Rated, ROHS Compliant
UL/CUL listed under UL60730. These models are all Complementary Listed to
"Emergency Lighting Equipment", (UL924) intended for Indoor Dry Locations.
This unit is pre-set for Plug n' Go™ operation, adjustment is optional.
Installation shall be in accordance with all applicable regulations, local and
NEC codes. Wire connections shall be rated suitable for the wire size (lead and
building wiring) employed.
For Class 2 DLM devices and device wiring: To be connected to a Class 2 power source
only. Do not reclassify and install as Class 1, or Power and Lighting Wiring.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However there is no guarantee that interference will not occur in
a particular installation. If this equipment does not cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interface by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult an experienced radio/TV technician for help
®
SPECIFICATIONS