Product Features - stayer MULTI L18 Instructions D'emploi

gb
This power tool has been designed for sawing
and cutting materials such as wood, plastic,
plaster, non-ferrous metals and fastening pieces
(i.e. unhardened nails, staples).
It is suited for low hardness wall tiles as well asn
sanding and dry scraping small surfaces.
It is is specially suited for close edge works as well
as screeding.
This power tool must be used exclusively with
STAYER accesories.
1_SAFETY WARNINGS FOR
PRECISION SAW
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts
of the power tool "live" and could give the
operator an electric shock.
• Use the machine only for dry sanding.
Penetration of water into the machine
increases the risk of an electric shock.
• Keep hands away from the sawing range.
Do not reach under the workpiece. Contact
with the saw blade can lead to injuries.
• Use suitable detectors to determine
if utility lines are hidden in the work
area or call the local utility company for
assistance. Contact with electric lines can
lead to fire and electric shock. Damaging a
gas line can lead to explosion. Penetrating a
water line causes property damage or may
cause an electric shock.
• When working with the machine, always
hold it firmly with both hands and
provide for a secure stance. The power
tool is guided more secure with both hands.
• Secure the
clamped with clamping devices or in a vice is
held more safely than by hand.
• Keep your workplace clean. Blends of
materials are particularly dangerous. Dust
from light alloys can burn or explode.
• Never use the machine with a damaged
cable. Do not touch the damaged cable
and pull the mains plug when the cable
is damaged while working. Damaged
cables increase the risk of an electric shock.
• Wear protective gloves when changing
application tools/accessories. Application
tools/accessories
prolonged usage.
workpiece. A workpiece
become hot
• Do not scrape wetted materials (e. g.
wallpaper) or on moist surfaces. Penetration
of water into themachine increases the risk of
an electric shock.
• Do not treat the surface to be worked
with solvent containing fluids. Materials
being warmed up by thescraping can cause
toxic vapours to develop.
• Exercise extreme caution when handling
the scraper. The accessory is very sharp;
danger of injury.
Products sold in GB only: Your product is fitted
with an BS 1363/A approved electric plug with
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted
in its place by an authorised customer service
agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid
a possible shock hazard and should never be
inserted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use
a residual current device (RCD) with a rated
residual current of 30 mA or less.
2_FUNCTIONAL DESCRIPTION
Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury. While reading
the operating instructions, unfold the graphics
page for the machine and leave it open.

PRODUCT FEATURES

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1. On/Off switch.
2. Thumbwheel for orbit frequency preselection.
3. Venting slots.
4. Tool holder.
5. Handle (insulated gripping surface).
6. Plunge saw blade.
7. Clamping bolt with spring washer.
Noise/Vibration Information
Measured sound values determined according to
EN60745. Typically the A-weighted noise levels
of the product are:
Sound pressure level 81 dB(A);
Sound power level 92 dB(A).
Uncertainty K=3 dB.
after
/ /
14