BTI A14,4-18 LG-2 Notice Originale page 7

CHARACTERISTICS
After inserting the battery into the reception of the charger the battery will
automatically be charged (red control lamp is illuminated continuously)
When a hot or cold battery pack is inserted into the charger (fl ashing red
lamp), charging will begin automatically once the battery reaches the correct
charging temperature (0°C...65°C). The max. charging current is fl owing
when the temperature of the Li-Ion-battery is between 0°C and 65°C.
The battery's charging time is between 1 min and 30 min (at 1,5 Ah),
depending on the state of discharge.
Once the battery is fully charged, the LED on the charger changes from red
to green.
It is not necessary to remove the battery after charging. The battery can be
stored permanently in the charger without the danger of being overcharged.
Under certain circumstances the charger may cause the LED indicators to
fl ash alternately red and green.
If this occurs, Remove the battery and reinsert.
If the LEDs still does not come on, remove pack(s) and unplug charger for at
least 2 minutes. After 2 minutes, plug charger back in and insert pack"
If both LEDs continue to fl ash, take the charger and battery out of use
immediately for safety reason and have them inspected by a BTI customer
service center.
LIGHT INDICATORS
Continuous red
Continuous green
Fast fl ashing red
Slow fl ashing red
Flashing red/green
MAINTENANCE
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualifi ed persons in order
to avoid a hazard.
Use only BTI accessories and spare parts. Components whose replacement
has not been described, can be exchanged at the BTI after sales service.
(BTI Befestigungstechnik GmbH & Co. KG · After Sales Service · Salt Road
51 · 74653 Ingelfi ngen · Tel 07940 / 141-870, -872, -873 or -886 · Fax 07940
/ 141-875)
If needed, an exploded view of the tool can be ordered. Please state the
ten-digit No. as well as the machine type printed on the label and download
the drawing at BTI Homepage www.bti.de > Service >
Explosionszeichnungen und Ersatzteillisten > BTI > Akku-Geräte or order
directly at BTI Befestigungstechnik GmbH & Co. KG, After Sales Service,
Salzstraße 51, 74653 Ingelfi ngen.
457 701 - BTI-A14-4-18LG-2.indd 7 457 701 - BTI-A14-4-18LG-2.indd 7
Charging
Charging is complete
Battery is too hot/cold - Charging will
begin when battery reaches correct
charging temperature
Battery charge is pending - Charging
will begin when the fi rst pack is fully
charged
Damaged or faulty battery pack
SYMBOLS
Please read the instructions carefully before starting the
machine.
Do not burn used battery packs.
Never charge a damaged battery pack.
Replace with a new one.
Do not dispose electric tools, batteries/rechargeable batteries
together with household waste material.
Electric tools and batteries that have reached the end of their
life must be collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for recycling advice
and collection point.
This tool is only suitable for indoor use. Never expose tool to
rain.
Class II tool.
Time-lag fuse 3.15 A
T3.15A
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked
before being dispatched from the manufacturing plant. If,
despite this fact, there are any defects, please send the item
directly to our Client Services Headquarters or to the nearest
service repair shop of the firm BTI.
BTI after sales service can be reached at the following contact
information: BTI Befestigungstechnik GmbH & Co. KG · After
Sales Service · Salz Straße 51 · 74653 Ingelfi ngen · Tel
07940/141 - 874 · Fax 07940 / 141-9874
The warranty period of 36 months for tools and 12 months for
batteries and chargers starts on the date of purchase which
must be verifi ed using the original receipt. During the guarantee
period the producer guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement for this is that the problem is a material and/or
manufacturing fault. Defects or faults caused by incorrect
treatment or excessive force are not covered by the warranty.
Furthermore, only original accessory parts may be used, which
BTI has expressly identifi ed as suitable for the operation with
BTI machines.
You can fi nd out the location of your nearest customer service
workshop in the address list at the back of this document.
7 ENGLISH
13.07.2020 10:26:58 13.07.2020 10:26:58