Publicité
Les langues disponibles
Les langues disponibles
Dear customer,
congratulations on your choice of purchase: the IMER CONCRETE
MIXER, the result of years of experience, is a very reliable machine
equipped with all the latest technical innovations.
- WORKING IN SAFETY
In order to be able to work in complete safety, the following
instructions must be read carefully.
This OPERATING AND MAINTENANCE manual must be kept
on site by the person responsible for the worksite, e.g. the site
foreman, and must always be available for consultation.
The manual should be considered as being an integral part of the
machine, and must be kept for future reference (EN 12100/2) until
the machine itself is disposed of. If the manual becomes damaged
or lost, a replacement can be obtained from the manufacturer.
The manual contains the declaration of conformity CE 98/37/CE
as well as important information on site preparation, installation,
use, maintenance operations and how to request spare parts.
In order that the safety of the operator, safe working and long
life of the equipment can all be guaranteed, the instructions in
this manual must be followed together with safety standards and
health and safety at work laws currently in force (use of suitable
footwear and clothing, use of helmets, gloves and goggles, etc.).
- Always make sure that signs are legible
,W LV VWULFWO\ IRUELGGHQ WR FDUU\ RXW DQ\ IRUP RI PRGL¿FD-
tion to the structure or working parts of the machine.
IMER INTERNATIONAL decline any responsibility in the case of
non-compliance with laws and standards governing the use of this
equipment. In particular: improper use, defective power supply,
ODFN RI PDLQWHQDQFH XQDXWKRULVHG PRGL¿FDWLRQV SDUWLDO RU WRWDO
failure to comply with instructions contained in this manual.
IMER reserves the right to modify the characteristics of the concre-
te mixer and/or the contents of this manual without any obligation
to update previous machines or manuals.
1. TECHNICAL SPECIFICATIONS
- The concrete mixer MINIBETA is equipped with class II
electrical protection, with double insulation (
7DEOH UHSRUWV WKH WHFKQLFDO VSHFL¿FDWLRQV RI WKH FRQFUHWH PL[HU
ZLWK UHIHUHQFH WR ¿JXUH
2. DESIGN STANDARDS
The concrete mixers have been designed and built in accordance
with the following standards: EN 12100-1-2, EN 60204-1, prEN
12151.
3. NOISE EMISSION LEVEL
Table 2 indicates the noise level produced by the mixer, measured
at the operator's ear (L
at 1 m - 98/37CE) and the environmental
pA
noise emission level (power L
WA
EN ISO 3744 (2000/14/EC).
4. DESCRIPTION AND ASSEMBLY OF THE CONCRETE
MIXER
- The concrete mixer is designed for use on construction
sites, for preparing and mixing concrete, mortars, cement
mixes, etc.
4.1 DESCRIPTION OF THE CONCRETE MIXER (Fig. 1)
The concrete mixer comprises a frame (ref. 7), drum rotation unit
(ref. 6), gearmotor mounting frame (ref. 5), two wheels (ref. 9) and
the drum tipping lever (ref. 3).
The gear motor (ref. 4) on the mounting frame (ref. 5) actuates
rotation of the mixing drum (ref. 1).
The electric power assembly and switch are located on top of the
electric motor (ref. 2).
4.2 CONCRETE MIXER ASSEMBLY
The IMER mixer arrives completely dismantled in a box.
IMER INTERNATIONAL S.p.A.
MINIBETA
).
) measured in accordance with
Remove all the machine components from inside the mixing drum.
Fig. 3-1) Insert the support (ref. 1) in the frame leg (ref. 2) and tighten
the nut and bolt, using a spanner n° 17.
Fig. 3-2) Mount the wheels and lock in position with the split - pins.
Fig. 3-3) Insert the drum rotation unit (ref. 1) and lock in position
using bolt (ref.2) and spanner n° 17.
Fig. 3-4) Hinge the motor and reduction gear assembly (ref. 1)
onto the drum rotation support (ref. 2) using hingepin (ref.3). Lock in
SRVLWLRQ XVLQJ WKH VSOLWSLQ ¿J
Fig. 3-6) Align the centre bush of the drum with the reduction gear
shaft.
- :DUQLQJ 7KH VORW LQ WKH GUXP EXVK PXVW ¿W RYHU WKH SLQ
on the reduction gear shaft.
Fig. 3-5
WRONG ASSEMBLY
POSITION FOR MOTOR-
MOUNTING PLATE.
Place washer (ref. 2) in position and tighten with bolt (ref. 1).
Fig. 3-7) Position the paddles inside the drum and lock in position
with nuts and bolts. Use spanner n° 19.
Finally, insert tipping lever (ref. 1) in the lever mounting tube and
lock by the cotter pin.
5. SAFETY INSTRUCTIONS
- Before using machine ensure all safety devices are
¿WWHG
- Keep all parts of body and/or tools clear of mixing drum
during operation.
Accident prevention standards and safety regulations must be
observed at all times in the work area.
When handling the components required to prepare the mixes,
take care not to raise dust that might be inhaled; should it be
impossible to avoid this, wear a protective mask over the mouth
and nose.
- The concrete mixer must never be used in areas at
ULVN IRU H[SORVLRQV RU ¿UHV RU LQ XQGHUJURXQG H[FDYDWLRQV
The concrete mixer is not equipped with lights, and therefore the
area where it is used must be well-lit.
Power supply lines must be installed where they will not be subject
to damage.
Do not stand the cement mixer on the electrical power cable.
Connection must avoid any contact of plugs with water. Only use
plugs and sockets with protection against water spray.
- Do not use electrical lines that are undersized, makeshift or
without the earth wire.
&RQVXOW TXDOL¿HG HOHFWULFLDQ LI XQFHUWDLQ
- Repairs to the electrical installation must only be carried out by
TXDOL¿HG SHUVRQQHO 'LVFRQQHFW PDFKLQH IURP SRZHU VXSSO\ DQG
stop motor before starting any maintenance operations or repairs.
-Avoid that electric conductors can get in touch with machine
movable parts and/or in mouvement and than, wearning to set
the metal parts in tension
6. ELECTRICAL SAFETY
The dual insulation cement mixer MINIBETA is manufactured in
DFFRUGDQFH ZLWK (1 VSHFL¿FDWLRQV LV SURWHFWHG DJDLQVW
MHWV RI ZDWHU ,3 DQG LV ¿WWHG ZLWK RYHUORDG DQG ORZ YROWDJH
protection devices.
The concrete mixer is also equipped with a safety device to pre-
vent accidental electrical contacts, with class II dual insulation of
all live parts. For this reason it does not require to be earthed.
- CAUTION: when carrying out repairs, class II protection
will only be maintained if original insulating materials are
used and provided the distances and insulating materials
7
CORRECT ASSEMBLY
POSITION FOR MOTOR-
MOUNTING PLATE.
Publicité
