Publicité
Reparaturen dürfen nur von Fachwerk-
stätten, die Original TIGRIP-Ersatzteile
verwenden, durchgeführt werden.
Nach einer erfolgten Reparatur sowie nach län-
gerer Standzeit ist das Lastaufnahmemittel vor
der Wiederinbetriebnahme erneut zu prüfen.
Die Prüfungen sind vom Betreiber zu
veranlassen.
TRANSPORT, LAGERUNG, AUSSERBE-
TRIEBNAHME UND ENTSORGUNG
Beim Transport des Gerätes sind
folgende Punkte zu beachten:
• Gerät nicht stürzen oder werfen, immer
vorsichtig absetzen.
• Geeignete Transportmittel verwenden.
Diese richten sich nach den örtlichen
Gegebenheiten.
Bei der Lagerung oder der
vorübergehenden Außerbetriebnahme
des Gerätes sind folgende Punkte zu
beachten:
• Das Gerät an einem sauberen, trockenen
und möglichst frostfreien Ort lagern.
• Das Gerät vor Verschmutzung, Feuchtigkeit
und Schäden durch eine geeignete Ab-
deckung schützen.
• Soll das Gerät nach der Außerbetriebnahme
wieder zum Einsatz kommen, ist es zuvor
einer erneuten Prüfung durch eine befähigte
Person zu unterziehen.
Entsorgung:
Nach Außerbetriebnahme sind die Teile des
Gerätes und gegebenenfalls die Betriebsstoff e
(Öle, Fette, etc.) entsprechend den gesetz-
lichen Bestimmungen der Wiederverwertung
zuzuführen bzw. zu entsorgen.
Weitere Informationen und Betriebs-
anleitungen zum Download sind unter
www.cmco.eu zu fi nden!
4 von 16
English
INTRODUCTION
Products of CMCO Industrial Products GmbH
have been built in accordance with the state-
of-the-art and generally accepted engineering
standards. Nonetheless, incorrect handling
when using the products may cause dangers
to life and limb of the user or third parties
and/or damage to the hoist or other property.
The operating company is responsible for
the proper and professional instruction of
the operating personnel. For this purpose, all
operators must read these operating instruc-
tions carefully prior to the initial operation.
These operating instructions are intended to
acquaint the user with the product and enable
him to use it to the full extent of its intended
capabilities. The operating instructions contain
important information on how to operate the
product in a safe, correct and economic way.
Acting in accordance with these instructions
helps to avoid dangers, reduce repair costs
and downtimes and to increase the reliability
and lifetime of the product. The operating
instructions must always be available at the
place where the product is operated. Apart
from the operating instructions and the
accident prevention act valid for the respec-
tive country and area where the product is
used, the commonly accepted regulations
for safe and professional work must also be
adhered to.
The personnel responsible for operation,
maintenance or repair of the product must
read, understand and follow these operating
instructions.
The indicated protective measures will only
provide the necessary safety, if the product
is operated correctly and installed and/or
maintained according to the instructions. The
operating company is committed to ensure
safe and trouble-free operation of the product.
CORRECT OPERATION
- The load lifting attachment is used for safely
transporting goods and material on pallets
which owing to their shape and dimensions
can be safely picked up by the fork tines.
ATTENTION: Always comply with the
instructions for application on sites.
- Any diff erent or exceeding use is con-
sidered incorrect. Columbus McKinnon
Industrial Products GmbH will not accept
any liability for damage resulting from
such use. The risk is borne by the user
or operating company alone.
- The load capacity indicated on the unit is the
maximum working load limit (WLL) that may
EN
be attached.
- The specifi ed load capacity applies for a
distance of the load centre of gravity of
400 mm or 500 mm (half tine length) from
the beam.
- Outside the area close to the ground or on
sites, the load must be secured by means
of the securing chain included in the scope
of supply which must be fi rmly tightened.
Eyes are provided on the vertical beam for
fi xing the chain.
- When the load is appropriately positioned
and the suspension eye is vertical above the
load centre of gravity (Fig. 2), the inclination
angle must be min. 5° to the rear (in the
direction of the vertical beam) when lifted.
- When transporting loose material, e.g. roof
tiles or building stones on site, a suitable net
or a suitable cage must be used in addition
as a protection against falling.
Note: The holes of the protection equipment
must be smaller than 50 mm
tion sheet „Packaged stones on sites" ZH
1/335).
- Do not allow personnel to stay or pass under
a suspended load.
- A lifted or clamped load must not be left
unattended or remain lifted or clamped for
a longer period of time.
- The operator may start moving the load only
after it has been attached correctly and all
persons are clear of the danger zone.
- When suspending the load lifting attach-
ment, the operator must ensure that neither
the load lifting attachment, the suspension
(e.g. hook, shackle, etc.) nor the load pose
a danger to himself or other personnel.
- Prior to operation of the load lifting attach-
ment in special atmospheres (high humidity,
salty, caustic, alkaline) or handling hazard-
ous goods (e.g. molten compounds, radioac-
tive materials) consult the manufacturer for
advice.
- The load lifting attachment may be used at
ambient temperatures between –40 °C and
+100 °C. Consult the manufacturer in the
case of extreme working conditions.
- The locking pin for adjusting the height of
the base frame upper part must always be
secured with the retaining clip.
- Always transport the load slowly, carefully
and close to the ground.
- The load lifting attachment must only be
guided and operated on the hand lever.
Danger of injury!
- For lifting and lowering, make sure the load
is in a stable position in order to avoid acci-
dents due to tipping, rolling or falling. This
also applies to loads stored on the side or
underneath.
2
(see informa-
Publicité
