Renkforce 1208071 Mode D'emploi page 4

Set-up
Place the radio-controlled clock on an even, horizontal surface. Use suitable padding
to protect valuable furniture from scratches.
Do not place the clock near heaters; shield it from direct sunlight. Otherwise
the room temperature cannot be accurately measured.
Manually starting DCF search
Briefly push the "WAVE" button (6). Now the search for the DCF signal begins, the
small radio tower display flashes at the top right of the display. Reception takes about
8 minutes, do not move the clock during this time, do not push any buttons (to stop the
search, push the WAVE button again).
You can also wait a day so the clock conducts the DCF search automatically
during the night when better reception is possible.
If the radio-controlled clock cannot receive the DCF signal, you can set the time manu-
ally.
Setting mode
• To enter setting mode, push and hold the SET button (2) for approx. 2 seconds.
• Now you can toggle between 12h and 24h mode (in 12h mode, PM appears next to
the time during the second half of the day).
Use the UP (3) and DOWN (5) buttons to change the displayed value; push and hold
to fast-forward.
Briefly push the SET button to move forward to the next setting. The order is:
12h/24h mode time zone hour
weekday.
The language for displaying the weekday can be switched between GER
(German), ENG (English), ITA (Italian), FRE (French), DUT (Dutch), SPA (Span-
ish) and DAN (Danish).
• Briefly push the WAVE button (6) to exit setting mode.
The clock automatically exits setting mode when no button is pushed for 30
seconds. Previously made settings will be saved.
For example, if you only change 12h/24h mode, the time zone or the language
for displaying the weekday, the radio tower symbol for DCF reception goes
out temporarily. However, the radio starts the DCF search at the next regular
synchronization time (1:00, 2:00, 3:00, 4:00 or 5:00 am).
Changing the temperature unit °C/°F
Briefly push the DOWN button (5) to switch the temperature unit between °C (Celsius)
and °F (Fahrenheit). The radio-controlled clock may not be in setting mode to change
this setting.
Alarm function
a) Activating/deactivating the alarm
• Briefly push the ALARM button (1) to turn the alarm function on/off. A small bell
symbol appears at the top of the display when the alarm is activated.
b) Setting the alarm time
• While in normal time display mode, push and hold the ALARM button (1) for approx.
3 seconds. The alarm hour indicator starts flashing.
• Push the UP (3) or DOWN (5) buttons to set the alarm time hour. Push and hold to
fast-forward.
• Briefly push the ALARM button (1), the alarm minute indicator starts flashing.
• Push the UP (3) or DOWN (5) buttons to set the alarm time minutes. Push and hold to
fast-forward.
• Briefly push the ALARM button (1) to save the setting and leave setting mode.
c) Activating snooze mode/deactivating the alarm
• At the set alarm time, the alarm sounds for 2 minutes and the bell symbol flashes.
• Push the SNOOZE • LIGHT button (4) to interrupt the alarm for 5 minutes. During this
time, the bell symbol and "Z " flash in the display (snooze mode is active). After 5
z
minutes, the alarm sounds again.
You can repeat this process several times.
• To turn off the alarm (or end snooze mode), push any button other than the
SNOOZE • LIGHT button.
minute year month date language for
Backlight
Briefly push the SNOOZE•LIGHT button (4) to activate the backlight. The backlight
turns off again after a few seconds to save electricity.
Maintenance and cleaning
The product is maintenance-free part from occasionally replacing the battery. Have
maintenance and repairs done by qualified experts or repair shops only. There are no
parts inside the radio-controlled clock that you need to maintenance, therefore never
dismantle the product, (apart from the process described in the user manual for insert-
ing/replacing the battery).
To clean the product, a dry, soft and clean cloth is sufficient.
Do not apply too much pressure to the display to prevent scratches, malfunction or
destruction of the display.
Use a longhaired, soft and clean brush and a vacuum cleaner to easily remove dust.
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solu-
tions as they can cause damage (discoloration) to the housing and malfunctioning.
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that
this product conforms to the fundamental requirements and the other relevant regula-
tions of the directive 1999/5/EC.
The Declaration of Conformity for this product can be found at:
www.conrad.com
Disposal
a) General
At the end of its service life, dispose of the product in accordance with rel-
evant regulatory guidelines.
Remove the (rechargeable) battery from the product and dispose of it sepa-
rately.
b) (Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used batter-
ies/rechargeable batteries. Disposing of them in the household waste is prohibited.
Contaminated batteries/rechargeable batteries are labelled with this symbol
to indicate that disposal in the domestic waste is forbidden.
Used (rechargeable) batteries can be returned to collection points in your
municipality, our stores or wherever (rechargeable) batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the envi-
ronment.
Technical data
Power supply ...................................... 1x AA/Mignon battery
Ambient conditions ............................ Temperature 0 °C to +50 °C, relative humidity 20%
Dimensions.......................................... 93 x 93 x 36 mm (H x W x D)
Weight .................................................. 117 g (without battery)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
to 90%, non-condensing