Asist AE3S80 Mode D'emploi page 41

aDDiTiONaL SaFETY iNSTrUCTiONS
• Keep out of reach of other people.
• Do not allow anyone to operate the device without
prior instruction. Also, do not allow children, mentally
unfit persons, people under the influence of drugs, me-
dications, alcohol or excessively tired people to opera-
te the device, and do not do so yourself.
• Do not allow other people, especially children, to in-
terfere with the work, touch tools or extension cord,
and prevent them from accessing the work area.
• Store unused tools well. When not in use, tools must
be stored in a dry, locked place out of the reach of
children.
• Wear the correct clothing. Do not wear loose clothing
or jewelry, as they may be caught in moving parts. •
Cover long hair with a protective headgear.
• Use protective equipment. Always wear eye protec-
tion!
• Protective equipment such as a respirator, non-slip
safety shoes, hard headgear or hearing protection,
used in accordance with the working conditions, redu-
ces the risk of personal injury.
• If dust is generated during work, use face or dust
masks. If you have devices for connecting the hood
and dust collector, make sure that they are connected
and used correctly.
• Observe the applicable regulations when sanding
painted surfaces and lead-based coatings. Persons
entering the work area must wear a dust mask.
• Avoid unintentional starting. Make sure the switch is
off when plugging the plug. Carrying a tool with your
finger on the switch or plugging in a tool fork with the
switch on can cause accidents.
• Remove any adjusting tools or wrenches before tur-
ning on the tool. Leaving an adjusting tool or wrench
attached to the rotating part of the power tool can
cause injury
persons.
• Before each use, the device and the cable must be
checked for damage.
• Only work where you can safely reach it. Always
maintain a stable posture and balance. This will give
you better control of the power tool in unforeseen si-
tuations.
• The device works safer and better in the specified po-
wer range, so do not overload it and do not use weak
devices under high loads.
To reduce the risk of fire or electric shock, do not expo-
se this apparatus to rain or moisture. This tool works
with life-threatening voltages. Replace a worn grinding
wheel in time. Never work on the inside of the tool and
have all repairs carried out by a qualified service tech-
nician.
BEFORE COMMISSIONING
Always make sure that the tool is switched off and
unplugged before starting work or making any adjus-
tments to the appliance.
Always wear safety goggles and a dust mask when
working with a plasterboard sander.
Never work without suction.
Follow national regulations.
- Use protective equipment against noise,
dust and vibrations !!!
KEEP THESE SAFETY INSTRUCTIONS FOR
FUTURE REFERENCE !!!
DESCriPTiON (a)
Plasterboard grinder is used for sanding
plasterboard ceilings and walls. It can also be used
to remove wallpaper, paints, adhesive residues and
plaster. The machine may only be used for its intended
purpose. Any other such overuse does not correspond
to the intended use. The resulting damage or injury of
all kinds is the responsibility of the user / operator and
not the manufacturer. Please make sure
that our devices were not intended for their intended
purpose
designed for trade, craft or
industrial use. We do not accept any liability if the
device is used in trade, craft or industrial enterprises
and in comparable activities.
1 dust extraction cap
2 front handles
3 protective brush
4 sanding discs
5 screw
6 dust extraction hoses
7 locking clamp
8 speed controller
9 switch
10 locking button
11 rear handle
12 LEDs
13 Suction adjustment knob
14 Telescopic handle
accessories
dust bag, 2m hose, 6xgrinding papers
(P120, P150 ,, P180, P240, P320, P400)
PiCTOgramS
Pictograms and values stated on the product
packaging:
a) Power supply values
b) Power consumption
c) Idle speed
(d) Grinding wheel Φ
a
USE aND OPEraTiON
The ASIST equipment and machines are designed for
domestic or hobby use only.
41
b c d