Publicité
12
TSP-AN Series
TSP-AN DSP Menu Structure
Fullrange
None
PROCESS
EQ
Live
Speech
Playback
User
Low/ High Shelving
Sub menu
Parametric 1 & 2
None
XOVER
HP 120 Hz
HP 100 Hz
-
-
TSP118B
User
Freq
Sub Menu
Phase
Auto
FBQ
Single
Learn
Reset
Subwoofer
Function
Sets the frequency response to the
None
default setting.
Sets the frequency response to
Live
a typical live sound setting.
Sets the frequency response for
Speech
optimal speech intelligibility.
Sets the frequency response ideal for
Playback
music playback.
Lets you defi ne your own frequency
User
response setting by entering the
corresponding sub menu.
Lets you defi ne a low and high
Low/ High Shelving
shelving fi lter.
Lets you defi ne a parametric bell-type
Parametric 1 & 2
EQ (Frequency, Qual. and Gain).
Unit is set for default full range /
-
subwoofer reproduction.
Preset with 120 Hz 24 dB / octave fi lter
LP 120 Hz
for crossover between subwoofer and
full-range speakers.
Preset with 100 Hz 24 dB / octave fi lter
LP 100 Hz
for crossover between subwoofer and
full-range speakers.
Preset with ideal settings for
TSP122
use in combination with TSP122
fullrange speaker.
Preset with ideal settings for
TSP152
use in combination with TSP152
fullrange speaker.
Preset with high pass alignment for
-
TSP118B subwoofer.
User crossover sub menu for
User
combination with other fullrange or
subwoofer speaker systems
Select the desired crossover frequency:
Freq
Fullrange systems: 75 Hz to 400 Hz
Subwoofer systems: 50 Hz to 150 Hz
Phase
Adjust the absolute phase (0° or 180°).
Automatically sets as many fi lters as
required. Whenever a new feedback
Auto
frequency is discovered, the fi rst fi lter
will be released to attenuate the new
frequency, and so forth.
Activates the FBQ (feedback detection)
Single
functionality, up to 8 feedback fi lters
Automatic procedure which searches
for feedback frequencies and locks
settings after all 8 fi lters have been set.
WARNING!
Learn
Please use ear protection during
this procedure. The feedback
signal may approach the system's
maximum level, which may cause
hearing damage!
Reset
Resets all fi lters.
Fullrange
Input
SETUP
INPUT
(page 1)
Volume
Sensitivity
Stand
POSITION
Wall
Ceiling
Corner
Delay
DELAY
Unit
Limit
LIMITER
Version
SETUP
(page 2)
1. - 20.
LOAD
1. - 20.
SAVE
Save Preset
Sub Menu
Contrast
SETUP
Quick Start Guide
13
Subwoofer
Function
Lets you choose the audio input
source. Choose between Local
Input
(analogue Input) or ULTRANET
(e.g., P16 monitoring system or
M32 audio via ULTRANET).
Adjusts the input gain. With
ULTRANET digital inputs over a range
Volume
from+ 10 dB to - 30 dB. With analogue
input from 0 dB to -∞ dB.
Adjusts input sensitivity for maximum
output when using an analogue source
Sensitivity
+4 dBu for normal operation, + 14 dBu
for high level input.
For positioning the speaker on a pole
Floor
mount stand (fullrange) or on the fl oor
(subwoofer).
For positioning the speaker on or next
Wall
to a wall (fi xed install); alternatively as
a monitor speaker (wedge).
For positioning the speaker on a wall
-
next to the ceiling (fi xed install).
For positioning the speaker in a corner
next to the ceiling (fi xed install);
Corner
For positioning the speaker in a corner
(subwoofer).
Adjusts the amount of delay
Delay
(max 300 msec = 103.08 m or
338.19 feet).
Selector between msec,
Unit
meter and feet.
Adjust the limiter threshold for the
input signal (from OFF down to
-30 dB). This threshold adjustment
Limit
allows you to set a max output power
which is below the speaker system's
rated max output.
Version
Displays the installed fi rmware version.
To load a specifi c preset, turn the
encoder to select the desired peset's
number, and then either the ENTER
1. - 20.
button or the encoder. When asked
to confi rm press the encoder again or
EXIT to abort.
To save a preset choose the
1. - 20.
respective preset slot and press
ENTER or the encoder.
Name the preset by choosing the
characters with the encoder and
Save Preset
pressing to confi rm each character.
When fi nished, press the ENTER
button to save the preset.
Adjust LCD panel contrast, The default
Contrast
contrast value is 15.
Publicité
