Beta 1924XM Notice D'utilisation Et Instructions page 7

�Beta
3/8" COMPACT IMPACT WRENCH item 1924XM
OPERATION MANUAL AND INSTRUCTIONS FOR AIR COMPACT IMP ACT WRENCH
&
CAUTION
1T IS IMPORTANT TO READ THIS MANUAL THOROUGHLY BEFORE USING THE PNEUMATIC
TOOL. FAILURE TO COMPLY WITH THE SAFETY STANDARDS ANO OPERATING INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY.
Store the safety instructins with care and hand them over to the us.ers.
PURPOSE OF USE
- The air compact impact wrench can be used for the following pu1rposes:
assembling threaded connecting parts
• screwing and unscrewing by means of impact sockets
• the angle impact wrench can also be used in open places exposed to water and air.
-
The air compact impact wrench must not be us.ed for the followi1119 operations:
the angle impact wrench musi noi be used with any hand sockets
the angle impact wrench must not be used with any couplers or extensions, because these result in reduced power of the impact
wrench and increased risk of breakage
the angle impact wrench musi noi be used in environments containing potentially explosive atmospheres
the trigger musi noi be locked with adhesive tape or clamps.
WORK AREA SAFETY
-
Beware of both surfaces thai may become slippery due lo the use of the machine and the danger of tripping aver the air hose.
-
While using the pneumatic tool lor jobs performed high !rom the ground, take ali necessary
risk to other workers, following the accidental falling of any tools (lor
&
Do noi operate the pneumatic tool in environments containing potentially explosive
generated, which can ignite the dust or fumes.
&
Avoid contaci with live equipment, because the pneumatic tool is noi insulated, and contaci with live parts can cause electric
shocks.
&
Keep children and bystanders away !rom your workplace while operating the pneumatic tool. Distractions !rom other people can
cause you to lose control
PNEUMATIC TOOL SAFETY
Do noi point the air flow to yourself or other people. Compresse,d air can cause serious injury.
-
Check the connections and the air supply lines. Ali
of pressure and air volume. Too low pressure impairs the functic,n of the pneumatic tool; too high pressure can cause damage
and/or injury.
-
Do not bend or tighten any hoses. Avoid using solvents and sharp edges. Keep the hoses away !rom
lmmediately replace any damaged hose. A detective feed pipe nnay cause uncontrolled movements of the compressed air pipe.
Raised rust or chips may cause eye injury. Make sure thai the hose clamps are always secured firmly.
PERSONNEL SAFETY
-
Stay alert; watch what you are doing. Do not use the pneumatic
medication.
-
Always use the following persona! protective equiprnent:
eye protection;
safety shoes;
gearing protection;
protective gloves against physical agents;
anti-vibration gloves, to be worn following a specially conductnd survey of the daily exposure of the hand-arm system to vibration.
-
Make sure you are in a sale position, keeping proper balance al ali times. A sale working position and a proper body posture
enable better contro! of the pneumatic tool in unexpected situations.
-
Do noi wear loose clothing or jewellery. Keep your hair, clothing and gloves away !rom moving parts. Loose
long hair can get caught in moving parts.
-
Do noi directly inhale the exhaust
water, oil, metal particles and impurities, which may cause haza1rds.
MANUFAC7rURED BY:
BETA UTENSILI S.P.A.
Via A. Volta 18,
20845, Sovico (MB)
Originai documentatlon drawn up In ITALIAN.
over the pneumatic tool.
units,
air, and prevent il from
ITA,LY
example, isolation of the work area and proper signs).
atmospheres,
couplers and hoses should conform to the produci specifications in terms
tool while tired or under the influence of drugs,
getting1 into your eyes. The exhaust air of the pneumatic tool can contain
precautions, to eliminate or minimize
because sparks may be
heat, oil and rotating parts.
alcohol, or
clothing, jewellery, and