RODCRAFT RH151 Manuel page 7

• A complete oil change is not necessary!
Please check the oil level at least once annually and refill, if necessary. Fill the cylinderwith hydraulic oil up to the lower edge of the oil inlet plug.
Please note that the piston mustbe retracted.
• Important: Too much oil can shut down the equipment.
• Only use hydraulic oil (type HLP ISO
• Maintenance and repair of the equipment only by technical maintenance staff
7. Air in the hydraulic system
There may be an air accumulation in the hydraulic system which may affect the performance of the trolley jack. To tackle this kind of problem please
proceed as follows
• Open the discharge valve by turning the lever rod anticlockwise whilst simultaneously pumping with the lever or by using the foot pedal (5-6 times).
• Afterwards, pump the jack up to its maximal height before lowering it again. The hydraulic system is de-aerated
8. Disposal
• The disposal of this equipment must be in accordance with the legislation the respective country.
• All damaged, strongly worn out or improperly functioning devices HAVE TO BE TAKEN OUT OF OPERATION.
The repair of the equipment should be performed only by qualified technical staff.
Use the equipment only for its intended use as described above, any other use is explicitly excluded! For injuries and damages resulting from improper
use, misuse or infringement of safety instructions, we accept no liability or warranty.
9. Trouble shooting( Translation)
Type of malfunction
Trolley Jack does not lift the load
Trolley Jack does not hold the load
Trolley Jack does not lift the load up to
the indicated maximum height
Saddle can not be lowered entirely
Trolley Jack lifts with difficulties
10. CE Certification
Valid for:
RH215/RH151/RH315
Origin of the product: Made in China
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating :
to „Machinery":
applicable harmonised standard(s) :
CP
Technical File
ZAC de la Lorie -38, rue Bobby Sands, B.P10273
available at the
44818 Saint-Herblain Cedex, France
EU Technocenter
Rodcraft Customer Center
Company name
Langemarckstr.35 bis
and address:
45141 Essen- Germany
We hereby declare that the following described machine complies with the general safety and health requirements of below mentioned EU directives due to its design and
conception and the type circulated by ourselves. This declaration becomes invalid if the machine is modified without our approval.
32) approved by the manufacturer. Please note:Never use brake fluid.
Possible Reason
1) The descent valve was not closed properly
2)Not enough oil
3) Too much oil in the reservoir
4) Same reason like in 1)
5)The hydraulic oil is contaminated with particles or dirt
6) Same reason as in 2)
7) There are air bubbles in the hydraulic system for instance from
transport
8 Same reason as in 5)
9) The spring /spring position 2 ,is /are not attached properly or worn out
10) Same reason as in 7)
11) Same reason as in 3)
EC DECLARATION
2006/42/EC (17/05/2006)
EN 1494:2000 + A1:2008
Visit our Internet presence at www.rodcraft.com
Here you can also download our manuals.
With further questions contact your nearest Rodcraft branch or the authorized dealer.
RODCRAFT PNEUMATIC TOOLS
EN
Cure
please colse the valve by turning the pump rod clock-wise
Low the saddle entirely and top up the hydraulic oil,unitl 4 mm under
rim of the oil plug on the cylinder
Please lower rhe lifting arm entirely and check the oil level. If the oil
level is higher than 4mm underneath the oil plug ,please remove some
oil from tank. The oil level should not be higher than 4mm underneath
the rim of the oil plug.
Please proceed as described in 1)
As a quick cure ,please turn the pump rod clockwise adn step on the
front wheel, pull up the lifting arm on the saddle entirely, release the
saddle and lower the lifting arm entirely bu turning the pump rod
anti-clockwise. Close the descent valve again by turning the pump rod
clockwise and try to use the tool again
Please proceed as described in 2)
Please proceed as described in 5)
Please proceed as described in 5)
Clean and lubricate all moving part regular and exchange all damaged
and worn part with new original parts
Please proceed as described in 5)
Please proceed as described in 3)
Serial: 011 to 129
Place and date
of issue:
Bruno Blanchet
General Manager
44818 Saint-Herblain,
France
01.06.2012
7