Here I'm in command
Making the right choice is important. And it's easy.
Programme selector knob
and programmed start
Use this knob to select the wash
programme.
Turn this knob clockwise only.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the knob.
Now press on/off button I (position
I), pilot lamp L will start flashing.
After 5", the setting will be
accepted, pilot lamp L will stop
flashing (staying lit) and the wash
cycle will begin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols (Stop/Reset) and wait
5" : when the cancellation has
been accepted, pilot lamp L
flashes, and you can then turn the
appliance off.
You can use this knob to delay
the appliance's operation.
Select one of the four delay time
positions, press the on/off button
I (position I) and wait 5". The
setting has now been accepted
(pilot lamp L stays lit) and you can
select the programme you desire.
Pilot lamp L has a particular
flashing motion (2" on and 4" off)
to indicate that a delayed start
has been set.
During this phase, you can open
the appliance door and change
the washing load, should you
wish to do so.
After the wash cycle has been set
and accepted by the washing
machine, turning the knob will
have no effect (except for when
it is on position
Stop/Reset).
The detergent dispenser with the
additional bleach compartment
is here.
Instructions for installation and use
15
D
Temperature control knob
It is used to set the wash tempe-
rature in the recommended
programme table on pag. 16. It
also allows you to reduce the tem-
perature recommended for the
selected programme, and even to
set a cold wash cycle ( ).
Spin exclusion knob
It is used to exclude the spin
cycle (by choosing symbol
or to reduce the spin speed of
the selected programme. The
maximum speed for the four
types of fabric are:
Fabric
Speed
Cotton
1400 rpm
Synthetics
800 rpm
Wool
600 rpm
Silk
no
Note: distribution phase will be
carried out at low speed.
Detergent dispenser
It is divided into three
compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle
wash;
3. Fabric conditioner.
4
3
2
1
Understanding the control panel
F
H
E
G
The washing machine is
equipped
with
an
compartment 4 (provided as an
accessory) for the bleach, to be
inserted in compartment 1.
Easy iron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron.
You can use it with programmes
3-4 (Cotton), 5-6 (Synthetics)
)
and 8-9 (Delicates).
Press
this
button
programmes 5-6-8-9 and the
wash cycle will come to a stop
on symbol
. You can comple-
te it by pressing button E again.
Important: this function should
not be used when button H
(stain removal) has been
pressed.
Extra Economy
Reduces water consumption
during the rinse cycles. We
recommend that you use this
function only with small laundry
loads, dosing the detergent
proportionally.
Rapid wash
This button reduces the length
of the wash programme by
about 30%. It cannot be used
with special programmes (see
page 16) or those for wool and
silk.
Stain removal (see page 19)
Thanks to this command, the
washing machine will carry out
a more intensive wash that
optimises the effectiveness of the
L
M
C
B
I
liquid additives, thus allowing
extra
more resistant stains to be
removed. When you press the
stain removal button, you cannot
activate the pre-wash.
On-off
When button I is pressed, the
washing machine is switched
on, when it is not the machine
is switched off.
Turning the appliance off
does not cancel the selected
programme.
in
The on-off lamp
Lamp L flashes when the
appliance is switched on and
awaiting a programme to be set.
A steady light means the
appliance has accepted the
selected programme.
The door block lamp
The safety lamp indicates that the
washing machine door is locked
to prevent it from being opened
accidentally. To avoid any
damages to lock mechanism,
you must wait for the lamp to
extinguish, before attempting to
open the door which takes around
three minutes.
A