Télécharger Imprimer la page

Publicité

Liens rapides

#PKGRIND9
Combo Salt Shaker & Pepper Grinder Kit
Kit Features:
• Overall height: 6-3/4"
• Convienient Salt & Pepper dispenser in one piece
• Easy to refill both Salt & Pepper
• Ceramic Grinder Mechanism
Required Accessories:
• 1-1/2" Forstner Bit: #FB150
• 1-1/16" Forstner Bit: FB1-116
• 1" Jam Chuck: #CJAM1
• Forstner Bit Extender: #FEX (Optional)
• Base Blank: 2-1/2" Min x 4" L (diameter can be as large as 3")
• Head Blank: 2-1/2" Min x 2" L (diameter can be as large as 3")
Adjusting
Nut
Boring the Blanks:
Base:
• Mark the center on both ends of the blank.
• Drill a 1-1/2" hole on each end, 3/8" deep at the base and 1/4" deep on the upper end.
• Drill a 1-1/16" hole through the entire blank, (bit extender is optional for this process) or drill half-way through and
turn around and drill through from the opposite end.
Note: If you drill the center hole from both ends to meet in the middle, be sure the ends of the blanks are 90º
square to obtain the best alignment of holes.
Head:
• Mark the center on both ends of the blank.
• Drill a 1-1/2" hole, 1/4" deep on the top end of the blank. Check to make sure the salt plate fits into this recess.
• Follow with a with a 1-1/16" diameter hole to the end.
2.5"
1-1/2"
DIAGRAM A / PARTS LAYOUT
Salt Shaker
Cap
Grinder Sleeve
Grinder Shaft
DIAGRAM B / BORING THE BLANKS
Head Blank
1/4"
1-1/16"
2"
Slot
Spring
Grinder Support
1/4"
Glue
1-1/2"
PSI Woodworking Products
Grinder Housing
Grinder Retainer
Grinder
Slot
Mounting Screws
Base Blank
1-1/16"
4"
3/8"
1-1/2"
2.5"

Publicité

loading

Sommaire des Matières pour PSI Woodworking Products PKGRIND9

  • Page 1 PSI Woodworking Products #PKGRIND9 Combo Salt Shaker & Pepper Grinder Kit Kit Features: • Overall height: 6-3/4” • Convienient Salt & Pepper dispenser in one piece • Easy to refill both Salt & Pepper • Ceramic Grinder Mechanism Required Accessories: •...
  • Page 2 PSI Woodworking Products #PKGRIND9 DIAGRAM D / TURNING THE BASE BLANK DIAGRAM C / TURNING THE HEAD BLANK Head Blank Base Blank 1” Expanding rubber Heavy Duty Live Jam Chuck 3 Jaw Center Drill Chuck Expanding Profile of your choice...
  • Page 3 Traduction des instructions de Penn State Industries (PSI) pour Duo salière/moulin à poivre Combo Salt Shaker & Pepper Grinder Kit Duo salière/moulin à poivre Kit Features: Caractéristiques de la trousse : • Overall height: 6-3/4” • Hauteur totale : 6 ¾ po •...
  • Page 4 Traduction des instructions de Penn State Industries (PSI) pour Duo salière/moulin à poivre • Follow with a with a 1-1/16” diameter hole • Poursuivez en perçant un trou de 1 1/16 po de diamètre to the end. jusqu’à l’autre extrémité. DIAGRAM B / BORING THE BLANKS DIAGRAMME B / PERÇAGE DES CARRELETS Head Blank...
  • Page 5 Traduction des instructions de Penn State Industries (PSI) pour Duo salière/moulin à poivre • Insert the assembly through the bottom of • Insérez cet assemblage dans l’orifice à la base du carrelet pour the base blank and push in. le corps et poussez à fond. •...