Allen + Roth WSLVCKJ Mode D'emploi page 6

ASSEMBLY INSTRUCTIONS
13. Using a stud finder (not included), locate the
edges of the wood studs. Find the center line of each
stud and draw a vertical reference line on the wall
over each one. Position installation template (R) at
desired location on wall.
Note: The bottom of the installation template (R)
should be no less than 31-1/2 in. from the floor.
Mark mounting holes with a pencil (not included) and
discard installation template (R). Drill 3/16 in. pilot
holes at marked locations. Then, with the beveled
edge facing up, attach the wall hanging cleats (I) with
large flat washers (JJ) and M8 x 2-1/2 in. lag bolts (II).
Hardware Used
M8 x 2-1/2 in. Lag Bolt
II
JJ Large Flat Washer
14. With the help from another person, carefully
hang the unit from mounting cleats (H) & middle
fixed Shelf (G) onto wall hanging cleats (I).
Long Shelf Installation
Note: If long shelf (K) needs cut to fit inside your
closet space, cut only one side of the shelf and do
not use a hacksaw. It is recommended you hire an
insured remodeler for this type of installation.
15. With a pencil, draw a level line at the desired
mounting location for long shelf (K). Using
L-brackets (KK) as a guide, mark the screw hole
locations with a pencil. Drill 3/8 in. diameter pilot holes
at least 2-1/2 in. deep at marked locations, then insert
wall anchors (RR) into the holes until they are flush
with the wall. Attach L-brackets (KK) to the wall using
M4 x 38 mm screws (UU) and to the long shelf (K)
using M4 x 14 mm wood screws (VA).
Hardware Used
KK L-Bracket
RR Wall Anchor
UU M4 x 38 mm Screw
VA M4 x 14 mm Wood Screw
13
Wooden Stud
16 in.
I
40.6 in.
I
R
Minimum 31-1/2 in.
14
x 4
x 4
H
I
G
15
K
x 4
x 8
UU
x 8
x 8
Lowes.com/allenandroth
10
ASSEMBLY INSTRUCTIONS
16. Attach long shelves (K) to left side panel (A) and
right side panel (B) with L-brackets (KK), securing
with M4 x 14 mm wood screws (VA).
JJ
Hardware Used
KK
II L-Bracket
VA
M4 x 14 mm Wood Screw
JJ
17. If you intend to install the Expandable Pole,
II
attach wood supports (J) on the inside of upper left
side panel (A) and/ or upper right side panel (B)
using wood screws (FF).
Note: The expandable pole should be installed to the
middle of wood support (J).
Hardware Used
FF M3.5 x 12 mm Wood Screw
Pole Installation
18. Insert 22 mm metal poles (T) into 25 mm metal
poles (S). Using closed pole holders (YC) as a guide,
mark screw hole locations with a pencil. Drill 3/8 in.
diameter pilot holes at least 2-1/2 in. deep at marked
locations, then insert drywall anchors (not included)
into the holes. Attach closed pole holders (YC) with
M4 x 38 mm zinc screws (ZZ). Insert 25 mm metal
poles (S) into closed pole holders (YC), securing with
M4 x 15 mm self-tapping screws (YY).
Note: Drywall anchors are not required if installing
into a stud.
Hardware Used
RR
YC
Closed Pole Holder
YY
M4 x 15 mm Self-tapping Screw
KK
ZZ
M4 x 38 mm Zinc Screw
VA
16
x 4
x 16
KK
17
x 12
J
18
S
YY
x 3
ZZ
x 3
YC Drywall Anchor
x 9
Lowes.com/allenandroth
11
K
VA
J
FF
T
YC